Create zones and global zones.
- On the Insert tab, click Zone or Global zone.
- Select the type of zone.
The appropriate dialog that appears. See the following steps for instructions for each type.
- To create an Avoid zone:
- Select Zone andAvoid.
- Enter a name.
- The Layer field is set to Avoid but it can be placed in any existing layer by selecting it from the list.
- Set the level of priority:
-
Apply High priority avoid zones to regions into which alignments cannot enter under any circumstances.
-
Apply Medium or Low priority avoid zones to regions into which alignments can enter, perhaps resulting in reduced costs or improvements to the geometry.
-
- Click OK.
Tip:
To create an object in a new layer that does not exist, type the name for a new layer in the Layer field while setting the properties of your feature.
- To create a Crossing or Water zone:
- Select Zone and Crossing or Water.
- Enter a name.
- The Layer field is set to Crossing or Water but it can be placed in any existing layer by selecting it from the list.
- Select the Reference Altitude:
-
The Local low is the lowest point on the DTM within 100 meters of the road being optimized.
-
The Mean sea level uses an absolute height above zero, this being the elevation at sea level.
-
The Natural surface is determined using the terrain model.
-
- In Crossing type, select the relevant type from the list.
-
To use the most economical means for crossing the area, select Unspecified. The most economical crossing type is normally earthworks, but in some cases it is more cost-effective to cross using a structure.
-
In an area where a particular crossing clearance is required, but where a crossing does not impact the type of construction, select Unspecified. For example, crossing a buried pipeline affects the clearance but not the type of construction.
-
- If you selected a crossing type other than Unspecified, select a structure type from the list.
Note: What you select here overrides the local default structure type. Select Unspecified to retain the local default structure type.
- Click OK.
- Trace the boundary of the zone on the Plan view.
- Double-click to stop the trace. There is no need to close the zone.
- To create a Local defaults zone:
- Select Zone and Local defaults.
- Enter a name.
- The Layer field is set to Local defaults but it can be placed in any existing layer by selecting it from the list.
- Select a local default for one or more of the following:
-
Bridge type
-
Tunnel type
-
Wall type
-
Geology type
-
Geometry type
The options include the following:
-
Unspecified: The local default zone will not affect the parameter. For example, selecting Unspecified for Geometry type will cause the zone to use the default geometry type. If the default is changed to another geometry type, the geometry of this zone will change to match it.
-
Global default: The parameter within the zone will be the same as the global default (marked with a blue tick).
-
New: Another dialog opens to enable you to define a new type for that parameter.
Note: What you select replaces the default for that item. If you only want to change one attribute (for example, only change the bridge type), set the values for all the other parameters as Unspecified. The default type will be used for these. You do not need to re-specify every type in a Local Defaults zone if the parameters you want to use are already specified in the default type. -
- Click OK.
- To create an Earthwork Limits zone:
- Select Zone and Earthwork Limits.
- Enter a name.
- Enter the Limits.
- Click OK.
- Trace the boundary of the zone in the Plan view.
- Double-click to close the zone.
- To create a Area Cost zone:
- Select Zone and Area Cost.
- Enter a name.
- The Layer field is set to Area cost but it can be placed in any existing layer by selecting it from the list.
- Select a corresponding Area cost type to associate with this zone.
- Click OK.
- In the Plan view, click to trace the outline of the zone.
- Double click to close the zone.
- To create a Linear Cost zone:
- Select Zone and Linear Cost
- Enter a name.
- The Layer field is set to Linear cost but it can be placed in any existing layer by selecting it from the list.
- Select a corresponding Linear cost type to associate with this zone.
- Click OK.
- In the Plan view, click to trace the outline of the zone.
- Double click to close the zone.
- To create a Global zone:
- Select Global Zone.
- Select the type of global zone. The process for defining the properties of global zones is similar to normal local zones, except that you do not need to trace a polygon boundary to define the zone.
- Global Crossing Zone
- Global Earthworks Limits Zone
- Global Area Cost Zone
- Global Linear Cost Zone