Skip to main content

Unfolding plates and profiles

Tekla Structures - Not version-specific zetwerk buiglijn uitslag k-waarde
Not version-specific
Tekla Structures
Environment
Construsoft European

An unfolding can be created from parts modeled in Tekla Structures as a polybeam. This can include both profiles and plates. In drawings, the unfolding setting is available in the Single-part drawing properties, which allows unfoldings of polybeams to be created. In the Single-part drawing properties dialog box, click the View creation button and go to the Attributes tab to unfold the part in the drawing:
 

Image
unfolding

 

Bent plate in the modelUnfolding in the drawing
Image
2016_12_23_13_58_082.png
Image
2016_12_23_13_58_123.png

The Unfold_corner_ratios.inp file

The following applies in order to create unfoldings:

The advanced option XS_USE_OLD_POLYBEAM_LENGTH_CALCULATION and XS_CALCULATE_POLYBEAM_LENGTH_ALONG_REFERENCE_LINE must be set to FALSE in Advanced options in the Dimensioning - unfolding category.
 

XS_DRAW_BENDING_LINE_DIMENSIONS_IN_UNFOLDINGThis advanced option must be set to TRUE to dimension bend lines of unfolded parts.
XS_DRAW_ANGLE_AND_RADIUS_INFO_IN_UNFOLDINGThis advanced option must be set to TRUE to dimension angles and radii of unfolded parts.
XS_ANGLE_TEXT_IN_UNFOLDING_BENDING_LINE_DIMENSIONINGThis advanced option is set to ANGLE= as the prefix text for the angle.
XS_RADIUS_TEXT_IN_UNFOLDING_BENDING_LINE_DIMENSIONINGThis advanced option is set to R= as the prefix for the radius.
XS_DRAW_INSIDE_ANGLE_IN_UNFOLDINGThis advanced option is set to TRUE to dimension the inside angle instead of the outside angle, for example 45° instead of 135°.
XS_UNFOLDING_ANGLE_DIM_FORMATThis advanced option is set to 2 as the format (decimals) for the angle text. These are the same values as on the General tab of the Dimension properties dialog box. Whole numbers can be used.
XS_UNFOLDING_ANGLE_DIM_PRECISIONThis advanced option is set to 100 and defines the precision of the angle text. These are the same values as on the General tab of the Dimension properties dialog box. Whole numbers can be used, for example 1, 2, 3, 4, 8, 16, 32, 10, 100, 1000.

The configuration file unfold_corner_ratios.inp contains settings that influence flat patterns. The file is stored in the folder ..:\TeklaStructures\<version>\Environments\ConstrusoftEuropean\General\ModelSettings, but it may also be saved in the model folder or in the ts folder. The parameters in this file define the location of the neutral line (where strain and stress are 0) when a profile is unfolded. The parameters are required when NC files are generated and when profiles are displayed unfolded in part drawings.

The contents of the file unfold_corner_ratios.inp:
 

Image
unfolding2

 

Image
openvouwen2
Image
1_CS_green
Type 1: profile
Type 2: plate
Image
6_CS_green
1: sharp bend
2: bend with a radius
Image
2_CS_green
Plate
Image
7_CS_green
Minimum angle sharp bend,
minimum radius bend with radius
Image
3_CS_green
Material grade
Image
8_CS_green
Maximum angle sharp bend,
maximum radius bend with radius
Image
4_CS_green
Minimum plate thickness
Image
9_CS_green
Calculation along inside, center line,
outside (.0, .5 or 1.0)
Image
5_CS_green
Maximum plate thickness  
Example 1: A bend plate with a thickness of 2 mm:
Image
openvouwen10

The last value in the file unfold_corner_ratios.inp is:

 

Image
openvouwen4


For plates with a thickness of up to 3 mm, the unfolding is calculated over the line .0. The other plates are calculated over the center, the line .5.

 

Image
openvouwen3
Example 2: A bend plate (Z shape):
Image
openvouwen8

The last value in the file unfold_corner_ratios.inp is:

 

Image
openvouwen5
Example 3: Bend beam IPE 300:
Image
2016_12_23_14_30_173.png

The last value in the file unfold_corner_ratios.inp is:
 

Image
openvouwen6

Never replace the second option in the file unfold_corner_ratio.inp with just a * !! When you modify the unfold_corner_ratio.inp file, Tekla Structures must be restarted and you must check the drawings. This depends on the modification you make. Keep in mind that changes (for example, the length in templates) are applied immediately when opening an existing drawing. If a profile is not defined, the center line (= 0.5) is used for the length calculation.
 

Image
2016_12_23_14_40_195.png
In the Beam properties, the Position on plane can be set on the Position tab (Left, Middle, Right). However, this does not shift the position of the neutral line.
Position on the plane: Left 
Neutral line on 0.5
Image
2016_12_23_14_41_506.png
Position on the plane: Right
Neutral line on 0.5
Image
2016_12_23_14_41_506.png

A bolt group in a polybeam

If a bolt group passes through two segments of a polybeam, the bolt group must be split. So one bolt group for one segment and one bolt group for the other segment.
 

1 bolt group2 bolt groups
Image
2016_12_27_07_36_304.png
Image
2016_12_27_07_34_523.png
Incorrect in drawingCorrect in drawing
Image
2016_12_27_07_42_565.png
Image
2016_12_27_07_43_216.png

This means that when the holes are created in the profile and the part is then bent, the holes will move along and ultimately end up in the correct position!

NC files of polybeams

Below is an example of an NC file of a plate with the .0 setting:

Image
2016_12_27_07_44_557.png
Image
2016_12_27_07_44_598.png

This drawing was generated with the length calculation along the inside, meaning the value .0 in the unfold_corner_ratio.inp file. The NC files are also created based on the settings in the unfold_corner_ratio.inp file. If you change the value from .0 to .5, the NC file will be adjusted accordingly.

Submit

Table of Contents