Skip to main content

Wooden roof (63)

Tekla Structures - Not version-specific
Not version-specific
Tekla Structures
Environment
Netherlands

Image
63_thumbnail

 

System component Wooden Roof (63) creates wooden roof elements based on stanchions, beams, and plates. 

Back to top

Created objects

  • Wooden roof elements.
Back to top

Used for

SituationDescription
Image
063_202
Roof elements
Image
063_203
(gable) roof
Image
063_203
Hip rafters
Image
063_204
Valley rafters
Back to top

Selection order

The component is placed by first setting out the contour of the roof element using polygon points (1) (triangle, quadrilateral, pentagon, polygon). This also determines the plane in which the element should be generated. After clicking the last polygon point, the selection of the polygon must be closed with the middle mouse button.


The next step is the direction of the rafters, which must be entered with 2 points (2). Finally, the position of the knee bracket must be clicked (3). Even when these do not need to be generated, the component requires these points for manual placement. The described pointing order is also indicated on the image tab.

Image
063_207

 

Use of component Timber Roof Panel (m025).
In component Timber Roof Panel (m025), it can be specified to call component Wooden Roof Element (63). Under Configuration, the setting created in component Wooden Roof Element (63) can be loaded.
 

Image
63_206

 

Image Tab

In the Image tab, the placement of the component is determined, as well as the prefix, start number, and export for any machines.

Image
63_001

 

OptionDescription
1Define whether a Hip Rafter or Valley Rafter should be generated on the relevant side of the element. Depending on the choice, the corresponding tabs become active. When General is selected, none of the rafter tabs are active. 
2Define whether a Hip Rafter or Valley Rafter should be generated on the relevant side of the element. Depending on the choice, the corresponding tabs become active. When General is selected, none of the rafter tabs are active. 
3Define the angle between both roof planes if hip or valley rafter solutions are required.
4Define the angle between both roof planes if hip or valley rafter solutions are required.
Classes for openings

When volumes are modeled for openings in the roof plane, component Wooden Roof Element 63 can take these into account. For each class, a setting can also be chosen for the Roof Window Component 64, which is called from component Wooden Roof Element 63. If the position or size of the solid is adjusted, component Wooden Roof Element 63 must be recalculated so that the new situation is used.

Image
63_018
Roof window macro settings

Enter the Class of the part that forms the opening and then the setting used by Roof Window Component 64.

Image
63_019
Offset listBy entering offset values here (separated by a space), both positive and negative offset values can be specified for each side of the element relative to the clicked points.
Position in depth

Displacement of the wooden wall perpendicular to the plane of the wooden wall (i.e., perpendicular to the plane in which the 3 points are located).

The dropdown list allows you to set the position relative to the points. The options are:

  • Front
  • Middle
  • Back

An additional displacement can be specified in the adjacent field.

Prefix assemblyPrefix of the roof element.
Start number markStart number of the roof element.
Name negative volume according toFor correct machine output in BTL or BVX format, it is necessary that the various generated cutouts receive the correct naming. Select the desired file format here. 

Parts 1 and 2 tab

In the Parts 1 and 2 tab, a total of 16 different profiles can be defined. In various tabs, these profile number(s) can be selected via a dropdown list. 

Image
63_003

 

OptionDescription
ProfileSelect a profile from the profile database.
Image
57_024
Reverse the start and end point of the profile (yellow and pink point). Used for asymmetric profiles.
PrefixPrefix of the part.
ClassClass of the profile.
Start num.Start number of the part.
MaterialMaterial of the part. Selectable from the material database.
CommentUser attribute (UDA) Comment of a profile.
NameName of the part.
ZoneIndicate in which zone the profiles should be placed. By default, this is set to 0.
Rotation

Rotation of the part. The options are:

  • Front
  • Top
  • Back
  • Bottom
FinishFinish of the part.

Parts rafters tab

In the Parts rafters tab, profiles and plates can be defined specifically for the tabs Left Valley, Left Hip, Right Valley and Right Hip.

Image
63_005

 

OptionDescription
ProfileThe properties are the same as those in the Parts 1 and 2 tab.
PlatesThe properties are the same as those in the Wooden plates tab.

Wooden Plates tab

In the Wooden Plates tab, four plates belonging to the roof element can be defined.

Image
63_004

 

OptionDescription
tThickness of the plate.
bWidth of the plate.
hLength of the plate.
Pos nr.Prefix of the plate.
Start num.Start number of the plate.
MaterialMaterial of the plate. Selectable from the material database.
NameName of the plate.
ZoneIndicate in which zone the plate should be placed.
FinishFinish of the plate.

Panel incl tab

In the Panel incl tab, the structure of the roof element is defined.

Image
63_007

 

OptionDescription
1Dropdown for the bottom tile batten (to be defined in the Parts 1 and 2 tab). If desired, a double tile batten can also be defined.
2Distance from the end of the element to the top of the first tile batten (D in example image/calculation).
3Option to enter a different distance for the next tile batten (D - E in example image/calculation). This value is not always applied directly. When the minimum tile batten spacing equals the maximum spacing C, this value will automatically adjust. The principle remains to always use whole roof tiles. See image and example calculation below.
4Dropdown for plate distribution at the top of the element. Any gaps between plates can also be defined here.
5Choice for a plate (to be defined in the Wooden plates tab) at the top of the roof element.
6Choice for standard tile batten profile (to be defined in the Parts 1 and 2 tab).
7Minimum tile batten spacing C.
Maximum tile batten spacing C.
8Choice for standard counter batten profile (to be defined in the Parts 1 and 2 tab).
9Position of the top tile batten and the end of the counter batten. Option to generate these dimensions horizontally or along the roof slope (A and B in example image/calculation).
10If one or more knee brackets are defined, you can also specify which type of plate should be used (to be defined in the Wooden plates tab) and how to handle full and leftover plates.
11Dropdown for plate distribution at the bottom of the element. Any gaps between plates can also be defined here.
12Define a maximum length for the counter battens and the location where the leftover piece should be generated (eaves or ridge side).
13

Option to place an extra part at the support beams for the knee bracket. Detail at the knee bracket.

Profile: Selectable profile (to be defined in the Parts 1 and 2 tab).

L: Length of the profile.

c: Distance the profile can be placed off-center from the support beam.

Image
63_020
Below are some images and an example of how the tile batten distribution is determined. The calculation always aims for whole roof tiles.

Measured distance in model:

L = 7053.74

Set in component 63:
A= 30
B= 70
Cmin = 312 / Cmax = 315
D= 45
E= 200
n = number of tile batten spacings

Image
063_208

n = (L – D – E - B) = (7053.74 – 45 – 200 – 70) / 315 = 21.39 
n’= n á =  21.39 á = 22  (rounded to 22)
C= (L – D – E - B) / n’ = (7053.74 – 45 – 200 – 70) / 22
C = 306.31

When a whole number of tile batten spacings must be generated and the available space (cmax; cmin) is too small, the algorithm may calculate a c value outside the range [cmin,cmax].
Note that cmin = cmax can also be specified; then the E value will automatically adjust. 

 

Panel horizontal Tab

In the Cross Section tab, the profiling and distribution for the rafters are defined, as well as the position of any leftover plate piece.

Image
63_008

 

OptionDescription
1Dropdown menu for the position of the leftover piece of the bottom plate.
Image
063_021
Leftover piece on the left side of the element.
Image
063_022
Leftover piece after the 1st full plate viewed from the left side of the element.
Image
063_022b
Leftover piece after the 2nd full plate viewed from the left side of the element.
Image
063_023
Leftover piece after the 3rd full plate viewed from the left side of the element.
Image
063_024
Leftover piece on the right side of the element.
Image
063_025
Leftover piece after the 1st full plate viewed from the right side of the element.
Image
063_026
Leftover piece after the 2nd full plate viewed from the right side of the element.
Image
063_027
Leftover piece after the 3rd full plate viewed from the right side of the element.
2Setback distance of the plate on the left side of the element relative to the rafter.
3Profile selection for intermediate rafters on full plates (to be defined in the Parts 1 and 2 tab).
4Gap between plates.
5Profile selection for intermediate rafters on the leftover plate (to be defined in the Parts 1 and 2 tab).
6Setback distance of the plate on the right side of the element relative to the rafter.
7Profile selection for the rafter profile on the left side of the element (to be defined in the Parts 1 and 2 tab).
8Define the widths of the bottom plates used in the cross section of the element.
9Profile selection for the rafter profile on the right side of the element (to be defined in the Parts 1 and 2 tab).
10Determine the number of rafters or the center-to-center spacing of the rafters on a full plate.
Image
63_028
No extra rafters.
Image
63_029
1 extra rafter evenly spaced (in the middle of the plate).
Image
63_030
2 extra rafters evenly spaced across the plate.
Image
63_031
3 extra rafters evenly spaced across the plate.
Image
63_032
X number of extra rafters with a center-to-center spacing not greater than the specified value.
Image
63_033
Possibility to define two different centre-to-centre distances in a single roof element.
11Determine the number of rafters or the center-to-center spacing of the rafters on a leftover plate.
Image
63_034
No extra rafters.
Image
63_035
1 extra rafter at a defined distance, measured from the left side.
Image
63_036
1 extra rafter at a defined distance, measured from the right side.
Image
63_037
1 extra rafter evenly spaced (in the middle of the plate).
Image
63_038
2 extra rafters evenly spaced across the plate.
Image
63_039
X number of extra rafters with a center-to-center spacing not greater than the specified value.
Rafter Connection 1Define the connection of rafters for non-rectangular elements (hip and valley rafters) at the bottom.
Image
63_040
Bottom rafter continues past the top rafter.
Image
63_041
Top rafter continues past the bottom rafter.
Rafter Connection 2Define the connection of rafters for non-rectangular elements (valley rafters) at the top.
Image
063_042
Bottom rafter continues past the top rafter.
Image
063_043
Top rafter continues past the bottom rafter.
Counter Batten ConnectionDefine the connection of counter battens for non-rectangular elements. Depending on the chosen option, additional dimensions can be specified.
Image
063_044
12: Distance from the counter batten of the upper roof element to the corner where the rafters of the lower and upper roof elements meet.
13: Distance from the counter batten of the lower roof element to the same corner.
Image
063_045
14: Clearance between counter battens.
Image
063_046
14: Clearance between counter battens.
Counter Batten Connection at RidgeConnections of counter battens at the ridge. Depending on the chosen option, additional dimensions can be specified.
Image
63_047

Counter batten is cut parallel to the global Z-direction.

15: Distance from the ridge to the counter batten.

Image
63_048

Counter batten is cut perpendicular.

15: Distance from the ridge to the counter batten.

16Offset for counter battens on the left side of the roof element. Both positive and negative values are possible.
17Offset for counter battens on the right side of the roof element. Both positive and negative values are possible.
18Offset for tile battens on the left side of the roof element. Both positive and negative values are possible.
19Offset for tile battens on the right side of the roof element. Both positive and negative values are possible.
Shortening Tile BattensFor non-rectangular elements, tile battens can be cut square at the ends or beveled according to the corresponding roof angle.
Image
063_049
Tile battens are cut square (perpendicular to the global Z-direction).
Image
063_050
Tile battens are cut at the sloping angle of the hip or valley rafter.
Gap between plates 

Bottom Detail Tab

In the Bottom Detail tab, the detailing of the underside of the roof element is defined. This includes the gutter detail, wall plate, and support beams.

Image
63_009

 

OptionDescription
1Setback distance of the gutter board.
2Profile selection for the gutter board (to be defined in Parts 1 and 2 tab).
3Clearance of the top plate relative to the wooden frame.
4Option to mount an extra bottom beam against the frame. Choose from those defined in the Parts 1 and 2 tab.
5Thickness of the edge profile.
6Profile selection for the edge profile. In this case, the thickness of the profile is defined at point 5 above. The height is determined by the geometry of the detail. All other properties such as name, material, and class are defined in the Parts 1 and 2 tab.
7Setback distance of the counter batten.
8Position of the support beam relative to the defined system point. Distance can be defined horizontally or along the roof slope.
9Distance at point 8 horizontally or along the roof slope.
10Choice of bottom detail and shape of the notch. Dimensions are described in the numbers above and below. The options are:
Image
63_080
Image
63_081
Image
63_082
Image
63_083
11Define the width of the horizontal part of the gutter board. Only available with option 2 (10).
12Length of the notch at the bottom. Option to define horizontally or equal to the roof angle.
13Height of the notch; if no notch is desired, set this distance to 0.
14Indicate with Yes or No whether a drill hole should be created through the rafter to the wall plate. This option is only available for semicircular wall plates (last options point 19).
15Diameter of the drill hole.
16Distance between the counter battens that must be left open for the drill hole.
17Profile selection for the support beam (to be defined in the Parts 1 and 2 tab).
18Profile selection for the wall plate (to be defined in the Parts 1 and 2 tab).
19Define the configuration for the support beam for the wall plate.
Image
63_084
No support beam is generated. Plate continues.
Image
63_085
No support beam is generated. Plate is interrupted by distance b.
Image
63_086

Rectangular support beam is generated.

Support beam profile is defined at point 9.

Image
63_087

Rectangular support beam is generated.

b: clearance between the plate and the support beam above and below.
Support beam profile is defined at point 9.

Image
63_088

T-shaped support beam is generated.

a: overlap where the plate rests on the support beam.
b: clearance between the plate and the support beam.
Support beam profile is defined at point 9.

Image
63_089

T-shaped support beam is generated.

a: overlap where the plate rests on the support beam.
b: clearance between the plate and the support beam.
c1: distance from the plate to the point where the bevel of the support beamstarts at the bottom (gutter side).
Support beamprofile is defined at point 9.

Image
63_090

T-shaped support beam is generated.

a: overlap where the plate rests on the support beam.
b: clearance between the plate and the support beam.
c1: distance from the plate to the point where the bevel of the support beam starts at the bottom (gutter side).
c2: distance from the plate to the point where the bevel of the support beam starts at the top (ridge side).
Support beam profile is defined at point 9.

Image
63_091

Semicircular wall plate and L-shaped support beam are generated.

a: overlap where the plate rests on the support beam.
b: clearance between the plates.
C1: vertical distance from the roof system point to the bottom of the wall plate.
C2: clearance between the top plate (ridge side) and the support beam.
f: distance from the center of the drill hole to the support beam.

20Distance to the front, middle, or rear of the support beam relative to point 8. To be defined horizontally or along the roof slope.
21Detail A: Depending on the choice, surrounding input fields become active and the size of the notch can be defined. The options are:
Image
63_092

Notch with plate at the bottom.

22: Distance from the plate to the end of the notch.
23: Plate choice under the notch (to be defined in the Wooden Plates tab).
24: Profile choice for 1 or 2 beams under the notch (to be defined in the Parts 1 and 2 tab).
a: Distance the plate rests on the L-shaped beam.
b: Spacing between beams under the notch.

Image
63_093

Notch with plate and beam at the bottom.

22: Distance from the beam to the end of the notch.
23: Plate choice under the notch (to be defined in the Wooden Plates tab).
24: Profile choice for 1 or 2 beams under the notch (to be defined in the Parts 1 and 2 tab).
b: Distance between the beam and the plate.

Image
63_094

Notch with plate and L-shaped beam at the bottom.

22: Distance from the beam to the end of the notch.
23: Plate choice under the notch (to be defined in the Wooden Plates tab).
24: Profile choice for 1 or 2 beams under the notch (to be defined in the Parts 1 and 2 tab).
a: Distance the plate rests on the L-shaped beam.
b: Clearance between the plate and the L-shaped beam.

Image
63_095

Notch with 2 beams at the bottom.

22: Distance from the beam to the end of the notch.
23: Plate choice under the notch (to be defined in the Wooden Plates tab).
24: Profile choice for 1 or 2 beams under the notch (to be defined in the Parts 1 and 2 tab).
b: Distance between the beams.

25Detail B: Define any additional beam at the notch. The options are:
Image
63_096

No extra beam.

b: Distance the plate is recessed from the start of the notch.

Image
63_097

Extra beam. Profile dimensions are determined by the height of the notch (13).

b: Distance the plate is recessed from the start of the notch at the bottom.
26: Width of the beam.
27: Profile choice for the beam (to be defined in the Parts 1 and 2 tab).
28: Distance the plate is recessed from the start of the notch at the top.

Image
63_098

Extra beam. The plate at the bottom of the notch is placed on the beam.

b: Distance the plate is recessed from the start of the notch at the bottom.
26: Width of the beam.
27: Profile choice for the beam (to be defined in the Parts 1 and 2 tab).
28: Distance the plate is recessed from the start of the notch at the top.

29Detail C: Additional options for positioning and orientation of the gutter board. The options are:
Image
63_099

Gutter board is placed under the roof slope angle.

30: Distance from gutter board to top of rafter.

Image
63_100

Gutter board is placed vertically, aligned with the global Z-axis of the model.

30: Distance from gutter board to top of rafter.

Detail top tab

In the Top Detail tab, the detailing of the top side of the roof element is defined. This includes the ridge detail and upper support beams.

Image
63_012

 

OptionDescription
1Choice for the execution of the top detail; depending on the choice, some values become active or are grayed out.
Image
63_10

Top beam positioned in the roof angle; define dimensions for the notch and various setback distances.

Details A-B-C can be defined separately.

Image
63_102

Split top beam positioned in the roof angle; define various dimensions for profiles, notch, and plate setback distances.

Details A-B-C can be defined separately.

Image
63_103

Top beam positioned vertically; define dimensions for the notch and various setback distances.

Details A-B-C can be defined separately.

Image
63_104

Split top beam positioned vertically; define various dimensions for profiles, notch, and plate setback distances.

Details A-B-C can be defined separately.

Image
63_105

Beveled top beam positioned in the roof angle; define dimensions for the notch and various setback distances.

Additional fields become available to define the width of the top beam at the top and bottom.

Details B-C can be defined separately.

Image
63_106

Option without ridge piece, rafters cut square; define dimensions for the notch and various setback distances.

Detail C can be defined separately.

Image
63_107

Option without ridge piece, rafters beveled; define dimensions for the notch and various setback distances.

Detail C can be defined separately.

2Setback distance from the ridge beam to the plate on top of the rafter.
3Width of the ridge beam.
4Height of the top beam.
5Setback distance from the ridge beam to the defined system point.
6Height of the bottom beam.
7Distance from the end of the rafters to the start of the bevel on the ridge beam.
8Height of the notch.
9Length of the notch and option to define the length horizontally or along the roof slope.
10Distance the plate is recessed in the notch relative to the outside of the ridge beam.
11Detail A: Detail of the top of the ridge beam. Options are:
Image
63_121

Rectangular ridge beam without notch, with horizontal top surface.

12: Length of the horizontal surface.
13: Profile choice for the ridge beam (defined in Parts 1 and 2 tab.
16: Width of the ridge beam.

Image
63_122

Ridge beam with notch.

12: Length of the horizontal surface.
13: Profile choice for the ridge beam.
14: Height of the notch.
15: Width of the notch.
16: Width of the ridge beam.

Image
63_123

Rectangular beam extending above the rafters.

12: Height the ridge plank extends above the rafters.
13: Profile choice for the ridge beam.

17
Option to enable or disable the ridge beam.
Image
63_124

Option to disable the ridge beam.

18: Profile choice for the ridge beam.

Image
63_125

Option to enable the ridge beam.

18: Profile choice for the ridge beam.

19Detail B: Options for generating a notch or an extra hinge batten. If the main detail (1) specifies a split top beam, the profile type and properties for this lower beam can be defined in Parts 1 and 2 tab. Depending on the choice, surrounding fields become active for notch dimensions, lower profile shape, and hinge batten.
Image
63_126
No notch at the bottom, partially beveled.
24: Clearance between inner plate and ridge plank.
Image
63_127
No notch at the bottom.
24: Clearance between inner plate and ridge plank.
Image
63_128
Notch at the bottom, partially beveled.
20: Width of the notch.
22: Height of the notch.
24: Clearance between inner plate and ridge plank.
Image
63_129
Includes hinge batten.
20: Width of the notch.
22: Height of the notch.
23: Distance from bottom of hinge batten to outside of ridge plank.
24: Clearance between inner plate and ridge plank.
25: Profile choice for hinge batten.
b: Clearance between hinge batten and inner plate.
Image
63_130
Includes hinge batten covering the bottom plate.
20: Width of the notch.
22: Height of the notch.
23: Distance from bottom of hinge batten to outside of ridge plank.
24: Clearance between inner plate and ridge plank.
25: Profile choice for hinge batten.
a: Distance the plate rests on the hinge batten.
b: Clearance between hinge batten and inner plate.
26Cover Plate
Image
63_131
Automatically generated cover plate.
Image
63_132
Automatically generated cover plate. Use the dropdown to define the desired profile.
27: Profile choice for the cover plate.
Image
63_133
Automatically generated cover plate combined with a distance relative to the specified intersection.
27: Profile choice for the cover plate.
28: Width of the profile depends on the defined distance, not the profile dimension.
29Detail C: Various options for the execution of the bottom of the notch. Depending on the choice, surrounding fields become active for dimensions and shape properties of the profile to be generated.
Image
63_188
No notch.
Image
63_189
Notch without beam.
b: Clearance between top plate and notch.
32: Clearance between bottom plate and notch.
Image
63_190
Notch with beam.
b: Clearance between top plate and notch.
31: Beam width.
32: Clearance between bottom plate and beam.
Image
63_191
Notch with beam.
b: Clearance between top plate and notch.
31: Beam width.
32: Clearance between bottom plate and beam.
Image
63_192
Notch without beam.
b: Clearance between top plate and notch.
32: Clearance between bottom plate and beam.
Image
63_193
Notch with beam.
b: Clearance between top plate and beam.
31: Beam width.
32: Clearance between bottom plate and beam.
Image
63_194
Notch with beam.
b: Clearance between top plate and beam.
31: Beam width.
32: Clearance between bottom plate and beam.
Image
63_195
Opening in the plate.
b: Width of the opening.
Image
63_196
Plate with support beam.
30: Profile choice for the support beam.
Image
63_197
Support beam is generated.
b: Clearance between plate and support beam.
 

Knee bracket Tab

In the Knee bracket tab, the support beams for the knee bracket can be defined.

Image
63_011

 

OptionDescription
1Horizontal distance from the roof system point to the first knee bracket.
2Horizontal distance from the roof system point to the second knee bracket.
3Vertical distance from the roof system point to the first knee bracket.
4Vertical distance from the roof system point to the second knee bracket.
Knee bracket 1Detail of the support beam.
5
Image
063_051
No support beam is generated. Plate continues.
Image
063_052
No support beam is generated. Plate is interrupted by distance b.
Image
063_053

Rectangular support beam is generated.

d: depth the support beam is placed into the plate.

Image
063_054

Rectangular support beam is generated.

b1: clearance between bottom plate (gutter side) and support beam.
b2: clearance between top plate (ridge side) and support beam.

Image
063_055

T-shaped support beam is generated.

a1: overlap where the plate rests on the support beam at the bottom (gutter side).
a2: overlap where the plate rests on the support beam at the top (ridge side).
b1: clearance between bottom plate and support beam.
b2: clearance between top plate and support beam.

Image
063_056

T-shaped support beam is generated.

a1: overlap bottom side.
a2: overlap top side.
b1: clearance bottom side.
b2: clearance top side.
c1: distance from plate to start of bevel on bottom side.

Image
063_057

T-shaped support beam is generated.

a1: overlap bottom side.
a2: overlap top side.
b1: clearance bottom side.
b2: clearance top side.
c1: distance to bevel start bottom side.
c2: distance to bevel start top side.

Image
063_058

Rectangular support beam is generated.

d: depth into plate.
c1: distance to bevel start bottom side.

6Extra offset relative to the defined system point for knee bracket position.
Image
063_068
Offset from system point to outside of support beam (ridge side) horizontally.
Image
063_069
Offset from system point to inside of support beam (gutter side).
Image
063_070
Offset from system point to outside of support beam (ridge side) along roof slope.
Image
063_071
No extra offset.
7Option to place an extra profile on the support beam.
Image
063_072
No extra profile.
Image
063_073
9: Profile choice for extra profile.
10: Offset extra profile to top of support beam.
e1: Shift in local x+ direction.
e2: Shift in local x+ direction.
L: Width of extra profile.
n: Number of profiles.
c: Spacing between angle brackets.
8Profile choice for knee bracket beam (defined in Parts 1 and 2 tab).
Knee bracket 2As with Knee bracket 1, details for Knee bracket 2 can be defined here.

Left Valley Tab

In the Left Valley tab, the detailing of the left valley rafter is configured.

Image
63_013

 

OptionDescription
1Choose a basic solution for the valley detail. Depending on this choice, the other details shown in the image can then be defined.
Image
63_136

Detail with rafters perpendicular to the roof plane.

2: Setback distance of tile batten relative to the first valley rafter.
3: Distance of counter batten to first valley rafter.
4: Distance of the valley rafter relative to the insertion point.
5: Distance of the bottom plate of the roof element relative to the insertion point.

Image
63_137

Detail with rafters positioned perpendicular to the valley gutter.

2: Setback distance of tile batten relative to the first valley rafter.
3: Distance of counter batten to first valley rafter.
4: Distance of the valley rafter relative to the insertion point.
5: Distance of the bottom plate of the roof element relative to the insertion point.

Image
63_138

Detail with valley rafters perpendicular to the roof plane and an extended top plate.

2: Setback distance of tile batten relative to the first valley rafter.
3: Distance of counter batten to first valley rafter.
4: Distance of the valley rafter relative to the insertion point.
5: Distance of the bottom plate of the roof element relative to the insertion point.

Detail EDetail E: Option to add multiple rafters parallel to the valley rafter.
Image
63_134
Option to add multiple rafters parallel to the valley rafter.
Image
63_135

Option to add one rafter and a plate to the valley rafter.

This option is only available when option 1 selects the type that places rafters perpendicular to the roof plane.

7: Plate on top of the valley.
8: Profile forming the valley rafter. Profile properties are defined in the Parts 1 and 2 tab.
9: Distance the plate is recessed relative to the valley rafter.
10: Distance the plate is recessed relative to the counter batten.

Image
63_135_5

Option to add one rafter, a plate, and an extra beam to the valley rafter.

6: Extra beam along the counter batten. Profile properties are defined in the Parts 1 and 2 tab.
7: Plate on top of the valley.
8: Profile forming the valley rafter. Profile properties are defined in the Parts 1 and 2 tab.

Detail ADetail A becomes active only when the first option in menu 1 is selected. Allows placement of extra beams horizontally and vertically.
Image
63_146
No extra beams.
Image
63_147

Two beams perpendicular to the valley rafter.

12: Profile choice for the upper extra beam.
13: Profile choice for the lower extra beam.
14: Start of bevel on lower beam.

Image
63_148

Two beams perpendicular to the valley rafter.

12: Profile choice for the upper extra beam.
13: Profile choice for the lower extra beam.
14: Start of bevel on lower beam.

Image
63_149

Vertical beam in the valley corner.

11: Start of bevel at top.
13: Profile choice for extra beam.
15: Vertical offset (global Z-axis).

Image
63_150

Horizontal beam.

13: Profile choice for extra beam.
15: Vertical offset (global Z-axis).

Image
63_151

Vertical beam in the valley corner.

11: Horizontal setback of extra beam relative to valley rafter.
13: Profile choice for extra beam.

Detail BDetail B: Plate underside of valley rafter.
Image
63_152
Plate cut square to roof slope.
Image
63_153
Plate cut perpendicular (parallel to global Z-axis).
Detail FDetail F: Extra beams under the valley.
Image
63_154
No extra beams under rafters.
Image
63_155

Two extra beams under rafters. Right beam runs under left beam.

16: Profile choice for left beam.
17: Profile choice for right beam.

Image
63_156

Two extra beams under rafters. Left beam runs under right beam.

16: Profile choice for left beam.
17: Profile choice for right beam.

Image
63_157

Two extra beams under rafters. Left and right beams meet without miter.

16: Profile choice for left beam.
17: Profile choice for right beam.

Image
63_158

Two extra beams under rafters. Left and right beams meet with miter.

16: Profile choice for left beam.
17: Profile choice for right beam.

Detail GDetail G: Top plate of roof element runs against or over valley rafter rafters. Only possible if a top plate exists (defined in Panel incl tab).
Image
063_139
Plate runs up to rafters.
Image
063_140
Plate runs over rafters.
18: Offset of plate to inner rafter.
Detail CDetail C: Define the number of extra rafters.
Image
063_141

No extra rafter.

19: Profile choice for rafter.

Image
063_142

1 extra rafter: optionally choose a different profile for the extra rafter. Default uses the main profile.

19: Profile choice for rafter.

20: Number of profiles that are added extra.

21: Profile choice for extra added rafter.

Image
063_143

2 extra rafters: optionally choose different profiles. Default uses the main profile.

19: Profile choice for rafter.

20: Number of profiles that are added extra.

21: Profile choice for extra added rafter.

Image
063_144

3 extra rafters: optionally choose different profiles. Default uses the main profile.

19: Profile choice for rafter.

20: Number of profiles that are added extra.

21: Profile choice for extra added rafter.

Image
063_145

Define in value field n the number of extra rafters: optionally choose different profiles. Default uses the main profile.

19: Profile choice for rafter.

20: Number of profiles that are added extra.

21: Profile choice for extra added rafter.

Left Hip Tab

In the Left Hip Rafter tab, the detailing of the left hip rafter is configured.

Image
63_014

 

OptionDescription
1Choose a basic solution for the hip rafter detail. Depending on this choice, the other details shown in the image can then be defined.
Image
063_160

Rafters positioned perpendicular to the roof plane.

2: Setback distance of tile batten relative to the first hip rafter.
3: Distance of counter batten to first hip rafter.
4: Distance of the hip rafter relative to the insertion point.
5: Distance of the bottom plate of the roof element relative to the insertion point.

Image
063_161

Rafters positioned aligned with the hip angle. Option to also define Detail A.

2: Setback distance of tile batten relative to the first hip rafter.
3: Distance of counter batten to first hip rafter.
4: Distance of the hip rafter relative to the insertion point.
5: Distance of the bottom plate of the roof element relative to the insertion point.

6In Detail D, an extra ridge beam, counter batten, and plate can be added.
Image
063_162
No components are added.
Image
063_163

An extra ridge beam is added.

7: Profile choice for extra ridge beam (defined in Parts 1 and 2 tab).

Image
063_164

An extra ridge beam is added with an option to define a filler plate under the ridge beam.

7: Profile choice for extra ridge beam.
8: Profile choice for filler plate.

Image
063_165

An extra ridge beam, counter batten, and horizontal beam are added.

7: Profile choice for extra ridge beam.
8: Profile choice for counter batten.
9: Profile choice for horizontal beam.

10Detail A becomes active only when the first option in menu 1 is selected. Allows placement of extra beams horizontally and vertically.
Image
063_166
No extra beams.
Image
063_167

Two beams perpendicular to the hip rafter.

11: Start of bevel on upper beam.
12: Profile choice for upper extra beam.
13: Profile choice for lower extra beam.

Image
063_168

Two beams perpendicular to the hip rafter.

11: Start of bevel on upper beam.
12: Profile choice for upper extra beam.
13: Profile choice for lower extra beam.

Image
063_169

Vertical beam in the hip corner.

12: Profile choice for extra beam.
14: Start of bevel at bottom.
15: Vertical offset (global Z-axis).

Image
063_170

Horizontal beam.

12: Profile choice for extra beam.
15: Vertical offset (global Z-axis).

Image
063_171

Vertical beam in the hip corner.

12: Profile choice for extra beam.
14: Hip rafter offset.
15: Start of bevel at top.

16Detail B: Finishing of the plate corner.
Image
063_176
Plate cut square to roof slope.
Image
063_177
Plate cut perpendicular (parallel to global Z-axis).
Image
063_178
Plate beveled at a defined angle.
17: Angle for beveling the plate end.
18Detail F: Extra beams under the hip connection.
Image
063_179
No beams under the hip connection.
Image
063_180
One beam under the hip connection.
19: Profile choice for beam.
21Detail G: Top plate of roof element runs against or over hip rafter rafters. Only possible if a top plate exists (defined in Panel incl tab).
Image
063_181
Plate runs up to rafters.
Image
063_182
Plate runs over rafters.
20: Offset of plate to inner rafter.
22Detail C: Define the number of extra rafters.
Image
063_183

No extra rafters.

23: Profile choice for rafter.

Image
063_184

1 extra rafter: optionally choose a different profile. Default uses the main profile.

23: Profile choice for rafter.

24: Number of profiles to be added.

25: Profile choice for extra rafters added.

Image
063_185

2 extra rafters: optionally choose different profiles. Default uses the main profile.

23: Profile choice for rafter.

24: Number of profiles to be added.

25: Profile choice for extra rafters added.

Image
063_186

3 extra rafters: optionally choose different profiles. Default uses the main profile.+

23: Profile choice for rafter.

24: Number of profiles to be added.

25: Profile choice for extra rafters added.

Image
063_187

Define in value field n the number of extra rafters: optionally choose different profiles. Default uses the main profile.

23: Profile choice for rafter.

24: Number of profiles to be added.

25: Profile choice for extra rafters added.

Right valley tab

The available options for the Right valley are the same as those for the left side but in the opposite configuration.

Image
063_015

Right Hip Rafter Tab

The available options for the Right Hip Rafter are the same as those for the left side but in the opposite configuration.

Image
63_017

Insulation Tab

In the Insulation tab, the properties of the insulation are defined.

Image
63_209

 

OptionDescription
tThickness of the insulation board. By entering a thickness, the insulation will be generated.
bWidth of the insulation board.
hHeight of the insulation board.
ProfileThe properties to define are the same as those in the Parts 1 and 2 tab.
Add InsulationIt is possible to add the insulation to the assembly: Yes or No.
1Define the various edge distances of the insulation relative to the frame components.

Foil Tab

In the Foil tab, the properties of the foil are defined.

Image
63_210

 

OptionDescription
Inner foilFoil on the underside of the roof element.
Outer foilFoil on the top side of the roof element.
ProfileDefine the properties of the foil on the underside of the element. Enter a value for thickness to generate the foil; if the thickness value is omitted, the foil will not be generated. The property settings are the same as those in the Parts 1 and 2 tab.
Add FoilIt is possible to add the foil to the assembly: Yes or No.
1Define the overlap lengths for the foil around the element on both the inside and outside. If the overlap length on the top side is specified and not on the underside, the value from the top field will be used, and vice versa. The same applies to left and right.

About tab

Information about the "build" date of the tool. This date may differ from the date in the tool you are using, but the content may nevertheless be the same. This date may be required when you contact the helpdesk.

 

Image
63_211
 

All rights reserved. No conclusions can be associated to the representation of the pictures in relation to the operating systems under which Tekla Structures runs.

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc-nd/4.0/ or send a letter to Creative Commons, 444 Castro Street, Suite 900, Mountain View, California, 94041, USA. 

Back to top
Submit