Skip to main content

Create roof and wall panels

Modified: 4 Jun 2026 Tekla Structural Designer 2026
2026
Tekla Structural Designer

Roof panels and wall panels are loading objects that allow you to apply panel loads, simple wind loads and loads calculated by the Wind Wizard to your structure.

Wall panels do not introduce any structural strength or stiffness to your structure. If you wish to introduce walls that resist gravity, or lateral loads, you must define them as concrete walls.

Roof panels can optionally introduce stiffness to your structure if you include them in diaphragms.

To create and modify roof and wall panels, see the following instructions.

Create roof panels

  1. On the Model tab, click Roof Panel.
  2. If you require the panel to act as a diaphragm, select Include in diaphragm in the Properties window, and then define the properties.
  3. If you are going to use the panel to apply loads calculated by the Wind Wizard select the Roof type.
  4. Click the start point of the panel.
  5. Click the remaining points of the panel.
  6. To define the end point of the panel, do one of the following:
    • Double-click the end point.

    • Click the end point, and click the start point again.

    Tekla Structural Designer creates a roof panel between the selected points.

Roof panel properties

Select one or more roof panels and then use the Properties window to view and modify their properties.

Property Description

Plane

Describes the level at which the panel was placed.

Name

The automatically generated name.

User Name

Can be used to override the automatically generated name if required.

Rotation angle

This value determines the following where appropriate:

  • Span direction for 1-way load decomposition
  • Orientation of semi-rigid 2D elements in the Solver Model

See: Rotation angle for slab items and panels and Modify slab/panel span direction

Include in diaphragm

The options are:

  • Checked

    The roof panel is meshed to form a diaphragm of semi-rigid 2D elements.

  • Unchecked (Default)

    No diaphragm is defined on the roof panel.

Thickness

Roof panel thickness

Note: Only displayed if "Include in diaphragm" is checked

Youngs Modulus

Youngs Modulus

Note: Only displayed if "Include in diaphragm" is checked

Shear Modulus

Shear Modulus

Note: Only displayed if "Include in diaphragm" is checked

Temperature coefficient

Temperature coefficient.

Note: Only displayed if "Include in diaphragm" is checked

Divide Stiffness by

Used to adjust the semi-rigid diaphragm (SRD) stiffness.

Note: Only displayed if "Include in diaphragm" is checked

RoofType

The options are:

  • Default (Default)
  • Flat
  • Monopitch
  • Duopitch
  • Hip Gable
  • Hip Main
  • Mansard
Note: The default option assigns the roof panel as flat (if the slope < 5 deg) or Monopitch (if the slope is > 5 deg). You can more accurately specify the roof panel by choosing the appropriate option from the list.
Note: If the RoofType is changed after the wind model has already been established, you will need run Update Zones to reinstate the zoning.

[+] UDA

Customizable list of the attributes that can be applied to individual members and panels.

See: Work with user-defined attributes

Create rectangular wall panels

  1. Open a structure or frame view within which you will create the wall panel.
  2. On the Model ribbon, in the Loading Objects group click the arrow under and select Wall Panel
  3. In the Properties window, ensure the Rectangular property is selected.
  4. Click the start point to define a corner of the panel.
  5. Click a point to define the opposite corner.
    Tekla Structural Designer creates a wall panel between the selected two points.
  6. Press the Esc key to end the command.

Create non-rectangular wall panels

  1. Open a structure or frame view within which you will create the wall panel.
  2. On the Model ribbon, in the Loading Objects group click the arrow under and select Wall Panel
  3. In the Properties window, ensure the Rectangular property is unselected.
  4. Click the start point of the panel.
  5. Click the remaining points of the panel.
  6. To define the end point of the panel, do one of the following:
    • Double-click the end point.

    • Click the end point, and click the start point again.

    Tekla Structural Designer creates a wall panel between the selected points.

  7. Press the Esc key to end the command.

Create wall panel parapet extensions

A parapet extension can only be created directly above an existing wall panel.
  1. Open a structure or frame view containing the existing wall panel above which you want to create a parapet extension.
  2. On the Model ribbon, in the Loading Objects group click the arrow under and select Parapet Extension
  3. In the Properties window, select the Parapet Extension Top method you require.
    • Horizontal - defined by a single horizontal level

    • Sloping - defined by two levels for a sloping parapet

    • Vertical End Offsets - defined by offsets at either end

    • Perpendicular Offset - defined by a single perpendicular offset to the wall top

  4. In the Properties window, enter appropriate levels or offsets.
  5. Click the start point of the panel.
  6. Pick the wall panel below where you want the parapet extension to be placed.
  7. Press the Esc key to end the command.
  8. In the Properties window set the remaining properties as required.
    Note: The Rotation angle is fixed as 90 degrees and can't be changed because parapet extensions can only decompose load vertically.

Create wall panel parapets

To ensure the wind analysis accounts for the parapet correctly, a wall panel parapet should only be created directly above an existing wall panel.
  1. Open a structure or frame view within which you will create the parapet wall panel.
  2. On the Model ribbon, in the Loading Objects group click the arrow under and select Wall Panel
  3. Click the start point of the panel.
  4. Click the remaining points of the panel.
    Note: You may need to create a new construction level to define the top level of the parapet.
  5. Press the Esc key to end the command.
  6. Select the newly created wall panel.
  7. Click the second wall panel.
  8. In the Properties window, change the Wind Panel Type to Parapet.
  9. In the Properties window, set the Rotation angle to define the direction of decomposition.

Wall panel properties

Select one or more wall panels and then use the Properties window to view and modify their properties. The properties for each wind panel type are described below.

Wind Wall
Plane Describes the plane in which the panel was placed.
Name The automatically generated name.
User Name Can be used to override the automatically generated name if required.
Wind Panel Type Wind Wall
Rotation angle

Describes the panel span direction as an angle, 0° is horizontal and 90° is vertical.

The direction can edited in the Properties window or graphically. To use the graphical method see: Modify slab/panel span direction

Gap Where the funneling gap to the adjacent building is not consistent due to the shapes of the buildings it is up to you to decide whether to specify the average or worst-case gap. The default gap is 1000 m which effectively give no funneling. A zero gap value explicitly means ignore funneling, for example where this building and the adjacent one are sheltered by upwind buildings.
Decompose to

Loads can be set to be decomposed to:

  • Members
  • Nodes (Default)
  • Rigid Diaphragms

See:Wall panel load decomposition

Note: The decompose to nodes option only applies to those loads generated by the wind wizard. It does not apply to those loads applied directly to panels.
Status Indicates whether the panel is valid or not.
Reverse

The front of each wall should be facing outwards in order to correctly determine the wind direction relative to the wall. Ensure that all the outward faces are displayed in the color assigned to the front of the wind wall.

If a wall is facing in the wrong direction, you can select this option to reverse it.

[+] UDA A customizable list of the attributes that can be applied to individual members and panels.
Parapet
Plane Describes the plane in which the panel was placed.
Name The automatically generated name.
User Name Can be used to override the automatically generated name if required.
Wind Panel Type Parapet
Rotation angle

Describes the panel span direction as an angle, 0° is horizontal and 90° is vertical.

The direction can edited in the Properties window or graphically. To use the graphical method see: Modify slab/panel span direction

Gap Where the funneling gap to the adjacent building is not consistent due to the shapes of the buildings it is up to you to decide whether to specify the average or worst-case gap. The default gap is 1000 m which effectively give no funneling. A zero gap value explicitly means ignore funneling, for example where this building and the adjacent one are sheltered by upwind buildings.

Solidity

[Not applicable for US wind code]

When the Wind Panel Type is set to Parapet, you also need to indicate the Solidity of the parapet. (Walls that are not parapets/parapet extensions automatically adopt a solidarity of 1.0).
Decompose to

When the Wind Panel Type is set to Parapet, loads are always decomposed to Members.

See: Wall panel load decomposition

Ignore local moments from lateral loading

When checked a lateral point load is applied to the top of the supporting column but the resulting out of plane local moments are ignored.

See: Wall panel load decomposition

Status Indicates whether the panel is valid or not.
Reverse

The front of each wall should be facing outwards in order to correctly determine the wind direction relative to the wall. Ensure that all the outward faces are displayed in the color assigned to the front of the wind wall.

If a wall is facing in the wrong direction, you can select this option to reverse it.

[+] UDA A customizable list of the attributes that can be applied to individual members and panels.
Parapet Extension
Plane Describes the plane in which the panel was placed.
Name The automatically generated name.
User Name Can be used to override the automatically generated name if required.
Wind Panel Type Parapet Extension
Rotation angle When the Wind Panel Type is set to Parapet Extension, the panel span direction if fixed at 90° to force loads to be decomposed vertically.
Gap Where the funneling gap to the adjacent building is not consistent due to the shapes of the buildings it is up to you to decide whether to specify the average or worst-case gap. The default gap is 1000 m which effectively give no funneling. A zero gap value explicitly means ignore funneling, for example where this building and the adjacent one are sheltered by upwind buildings.

Solidity

[Not applicable for US wind code]

When the Wind Panel Type is set to Parapet Extension, you also need to indicate the Solidity of the parapet. (Walls that are not parapets/parapet extensions automatically adopt a solidarity of 1.0).
Decompose to

When the Wind Panel Type is set to Parapet Extension loads can be set to be decomposed to:

  • Members
  • Nodes (Default)

See: Wall panel load decomposition

Ignore local moments from lateral loading

When checked, the resulting out of plane local moments are ignored.

See: Wall panel load decomposition

Status Indicates whether the panel is valid or not.
Reverse

The front of each wall should be facing outwards in order to correctly determine the wind direction relative to the wall. Ensure that all the outward faces are displayed in the color assigned to the front of the wind wall.

If a wall is facing in the wrong direction, you can select this option to reverse it.

[+] UDA A customizable list of the attributes that can be applied to individual members and panels.
Submit

Table of Contents