Skip to main content

Bent plate (151)

Modified: 21 Jan 2021 Tekla Structures 2026
2026
Tekla Structures

Bent plate (151) connects a beam to a column or a beam using one or two bolted or welded bent plates. The end of the beam can be cut square or bevel to accommodate a sloping secondary beam. By default, notches are created to the secondary beam flanges when needed. You can define on which side of the secondary beam web the bent plate is placed in single plate connections. Double plate connections can also be created. Haunch plates are created welded to the secondary beam flanges when required.

Objects created

  • Bent plates

  • Haunch plates

  • Stiffeners

  • Bolts

  • Cuts

  • Welds

Use for

Situation Description

Beam connected to a column using a bent plate.

Selection order

  1. Select the main part (column or beam).

  2. Select the secondary part.

    The connection is created automatically when the secondary part is selected.

Part identification key

Description

1

Bent plate

2

Haunch plate

Picture tab

Use the Picture tab to define the connection dimensions.

Dimensions

Description

1

Distance between the main part and the secondary part (beam). By default, the distance is 20 mm.

2

Haunch plate height to the beginning of the chamfer.

3

Haunch plate width to the beginning of the chamfer.

4

Distance from the bent plate edge to the lower flange notch.

You can define this dimension if the plate extends below the bottom of the secondary beam.

Beam end cut

Define how the secondary beam end is cut. The beam is viewed from the side.

Option

Description

Default

Bevel

AutoDefaults can change this option.

Automatic

If the secondary beam is sloped less than 10 degrees, the beam end is cut square. Otherwise, the beam end is cut bevel.

Square

Cuts the end of the secondary beam square.

Bevel

Cuts the end of the secondary beam parallel to the edge of the main part.

Beam flange cut

Define how the secondary beam flange end is cut. The beam is viewed from the top.

Option

Description

Default

Bevel

AutoDefaults can change this option.

Bevel

Cuts the end of the flange bevel.

Square

Cuts a part of the flange square and leaves a part of it bevel.

Haunch plate creation

Options Description

Default

Haunch plates are not created.

AutoDefaults can change this option.

Haunch plates are not created.

Top and bottom haunch plates are created.

Top haunch plate is created.

Bottom haunch plate is created.

Parts tab

Use the Parts tab to define the bent plate properties and positions.

Parts

Option Description

Bent plate NS

Thickness of the near side bent plate.

Bent plate FS

Thickness of the far side bent plate.

Top Web Ext

Thickness, width and height of the top web extension.

Btm Web Ext

Thickness, width and height of the bottom web extension.

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

Finish

Describes how the part surface has been treated.

Dimensions

Description

1

Gap between the right bent plate and the main part.

2

Gap between the left bent plate and the main part.

3

Gap between the right bent plate and the secondary part.

4

Gap between the left bent plate and the secondary part.

5

Collision plane change.

Bent plate position

Default

Creates two bent plates, near side and far side.

AutoDefaults can change this option.

Automatic

Near side and far side bent plates are selected automatically.

Near side bent plate

Far side bent plate

Far side switched

Creates a far side bent plate with a leg pointing to the near side.

Near side switched

Creates a far side bent plate with a leg pointing to the far side.

Creates two bent plates, near side and far side.

Attachment to the main part

Option Description

Default

The bent plate is bolted to the main part.

AutoDefaults can change this option.

Automatic

The bent plate is bolted to the main part.

The bent plate is bolted to the main part.

The bent plate is welded to the main part.

The bent plate is bolted and welded to the main part.

Attachment to the secondary part

Option Description

Default

The bent plate is bolted to the secondary part.

AutoDefaults can change this option.

Automatic

The bent plate is bolted to the secondary part.

The bent plate is bolted to the secondary part.

The bent plate is welded to the secondary part.

The bent plate is bolted and welded to the secondary part.

Attachment point control

Option Description

Default

The collision plane is not changed from the default position.

AutoDefaults can change this option.

The collision plane is not changed from the default position.

The collision plane is changed to the nearest surface.

The collision plane is changed to the farthest surface.

Top notch / Btm notch tab

Use the Top notch and Btm notch tabs to define the notch settings and dimensions.

Notch dimensions

Option Option

Description

1

Horizontal dimension for the notch clearing.

The distance is measured from the intersection point of three planes: top or bottom of the flange plane, end of the flange plane, and the inner web or side surface, depending on the type of clearance selected.

2

Vertical dimension for the notch clearing.

The distance is measured from the intersection point of three planes: bottom of the flange plane, end of the flange plane, and the inner web or side surface, depending on the type of clearance selected.

3

Horizontal dimension for the notch override.

The distance is measured from the intersection point of three planes: top of the flange plane, fitting plane, and the inner web or side surface, depending on the type of clearance selected.

4

Vertical dimension for the notch override.

The distance is measured from the intersection point of three planes: top of the flange plane, fitting plane, and the inner web or side surface, depending on the type of clearance selected.

5

Radius of the notch cut.

6

Vertical notch orientation.

Notch settings

Do notch

  • Yes enables notching.

  • No disables notching, but does not disable stripping and flange coping.

    Use the Strip / Cope options for disabling stripping and flange coping.

Type of clearance

  • Side with flange

    Use the main part flange and the inner side plane of the secondary part as a reference for the clearing.

  • Web with plate

    Use the inner shear tab plane and the inner web plane of the secondary part as a reference for the clearing.

  • Web with flange

    Use the flange of the main part and the inner web plane of the secondary part as a reference for the clearing.

Strip/Cope option

  • Automatic strip

    Based on the shear tab shape and edges, the connection strips the secondary part flanges as necessary.

  • Never strip or cope

    Stripping or coping is not done.

  • Force strip

    Connection always strips, even when the shear tab edges are not clashing or close to the secondary part flanges. Set the notch cut length in Forcing Dist and the depth in Force Depth.

  • Automatic flange cope

    Based on the shear tab shape and edges, the connection copes the secondary part flanges as necessary.

  • Force flange cope

    The connection always copes, even when the shear tab edges are not clashing or close to the secondary part flanges. Set the notch cut length in Forcing Dist and the depth in Force Depth.

  • Strip also other side

    Both secondary part flanges are stripped.

Flange cut options

Define the flange cut dimensions and the cut thickness.

Description

1

Dimension for additional flange cut.

The dimension is measured from the end of the beam if not fitted, or from the fitting surface if fitted.

2

Dimension for additional flange cut.

The dimension is measured from the center line of the beam.

Vertical notch orientation

Bottom

Default

Square to the secondary part.

AutoDefaults can change this option.

Automatic

Square to the secondary part.

Square to the secondary part.

The notch is cut vertically square relative to the secondary part.

Square to main part

The notch is cut vertically square relative to the main part.

Notch orientation

Option Description

Default

Square to the main part.

AutoDefaults can change this option.

Automatic

Square to the main part.

Square to the secondary part.

The notch is cut horizontally square relative to the secondary part.

Square to the main part.

The notch is cut horizontally square relative to the main part.

Flange cuts tab

Use the Flange cuts tab to define how the flanges are cut.

Dimensions

Description

1

Transversal dimension

2

Longitudinal dimension

3

  • Top: Top flange is cut.

  • Bottom: Bottom flange is cut.

  • Both: Both the top and the bottom flange are cut.

4

  • Near: Near side is cut.

  • Far: Far side is cut.

  • Both: Both the near and far side are cut.

Stiffeners tab

Use the Stiffeners tab to control the stiffener plate dimensions, orientation, position, and type.

Stiffener plate dimensions

Option Description

Top NS

Thickness, width, and height of the top near side stiffener.

Top FS

Thickness, width, and height of the top far side stiffener.

Bottom NS

Thickness, width, and height of the bottom near side stiffener.

Bottom FS

Thickness, width, and height of the bottom far side stiffener.

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

Finish

Describes how the part surface has been treated.

Stiffener orientation

Option

Description

Default

Stiffeners are parallel to the secondary part.

AutoDefaults can change this option.

Stiffeners are parallel to the secondary part.

Stiffeners are perpendicular to the main part.

Stiffener creation

Option

Description

Default

Stiffeners are created.

AutoDefaults can change this option.

Automatic

Stiffeners are created when necessary.

No stiffeners are created.

Stiffeners are created.

Stiffener shape

Option

Description

Default

Line chamfered stiffener plates

AutoDefaults can change this option.

Automatic

Line chamfered stiffener plates

Square stiffener plates

Stiffener plates with a gap for the main part web rounding

Line chamfered stiffener plates

Stiffener gap

Option

Description

Size of the gap between the flanges and the stiffener.

Chamfer type

Option

Description

Default.

Line chamfer

AutoDefaults can change this option.

No chamfer

Line chamfer

Convex arc chamfer

Concave arc chamfer

Stiffener positions

Description

1

Size of the gap between the stiffener and the beam web edge.

2

Size of the gap between the top near side stiffener and the beam flange edge.

3

Size of the gap between the bottom near side stiffener and the beam flange edge.

4

Size of the gap between the bottom far side stiffener and the beam flange edge.

5

Size of the gap between the top far side stiffener and the beam flange edge.

Bolts tab

Use the Bolts tab to control the bolt group dimensions and bolt properties.

Bolt group dimensions

Description

1

Select main bolted part: beam or bent plate.

2

Bolt edge distance.

Edge distance is the distance from the center of a bolt to the edge of the part.

3

Number of bolts.

4

Bolt spacing.

Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.

5

Select how to measure the dimensions for vertical bolt group position.

  • Top: From the upper edge of the secondary part to the uppermost bolt.

  • Middle: From the center line of the bolts to the center line of the secondary part.

  • Below: From the lower edge of the secondary part to the lowest bolt.

6

Bolt edge distance.

Edge distance from the center of the bolt to the top of the beam.

Description

1

Select the location where the bolts should be attached.

2

Bolt edge distance.

Edge distance is the distance from the center of a bolt to the edge of the part.

3

Number of bolts.

4

Bolt spacing.

Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.

5

Define which bolts are deleted from the bolt group.

Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom.

Bolt alignment

Main bolt alignment Secondary bolt alignment Description

Default

Square to the secondary part.

AutoDefaults can change this option.

Automatic

Square to the secondary part.

Square to the secondary part.

Square to the main part.

Vertically staggered.

Horizontally staggered.

Bolt basic properties

Option

Description

Default

Bolt size

Bolt diameter.

Available sizes are defined in the bolt assembly catalog.

Bolt standard

Bolt standard to be used inside the component.

Available standards are defined in the bolt assembly catalog.

Tolerance

Gap between the bolt and the hole.

Thread in mat

Defines whether the thread may be within the bolted parts when bolts are used with a shaft.

This has no effect when full-threaded bolts are used.

Yes

Slotted holes

You can define slotted, oversized, or tapped holes.

Option

Description

Default

1

Vertical dimension of slotted hole.

0, which results in a round hole.

2

Horizontal dimension of slotted hole, or allowance for oversized holes.

0, which results in a round hole.

Hole type

Slotted creates slotted holes.

Oversized creates oversized holes.

No hole does not create holes.

Tapped creates tapped holes.

Rotate Slots

When the hole type is Slotted, this option rotates the slotted holes.

Slots in

Part(s) in which slotted holes are created. The options depend on the component in question.

Bolt assembly

The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.

If you want to create a hole only, clear all the check boxes.

To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.

Bolt length increase

Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.

Staggering of bolts

Option

Description

Default

Not staggered

AutoDefaults can change this option.

Not staggered

Staggered type 1

Staggered type 2

Staggered type 3

Staggered type 4

Staggering of bolts on clip angle

Option

Description

Default

Bolts are not staggered.

AutoDefaults can change this option.

Bolts are not staggered.

The bolts that connect the clip angle to the secondary part are on the same horizontal level as the bolts that connect the clip angle to the main part.

Bolts on the main part are staggered.

The bolts that connect the clip angle to the main part are moved downwards by half the bolt vertical spacing value.

Bolts on the secondary part are staggered.

The bolts that connect the clip angle to the secondary part are moved downwards by half the bolt vertical spacing value.

Bolts on the secondary part are staggered.

The bolts that connect the clip angle to the sloped secondary part are parallel to the secondary part.

Beam cut tab

Use the Beam cut tab to control weld backing bars, weld access holes, beam end preparations, and flange cuts.

Weld backing bar

Option Description

Backing bar

Thickness and width of the weld backing bar.

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

Finish

Describes how the part surface has been treated.

Weld access hole dimensions

Description

1

Gap between the secondary part top flange and the main part.

2

Vertical dimensions for the top and the bottom weld access holes.

3

Horizontal dimensions for the top and the bottom weld access holes.

4

Gap between the secondary part web and the main part.

Tekla Structures adds the value you enter here to the gap you enter on the Picture tab.

5

Gap between the secondary part bottom flange and the main part.

Tekla Structures adds the value you enter here to the gap you enter on the Picture tab.

Weld access holes

Option

Description

Default

Default

Round weld access hole

AutoDefaults can change this option.

Round weld access hole

Square weld access hole

Diagonal weld access hole

Round weld access hole with a radius that you can define in

Extended cone-shaped weld access hole with a radius and dimensions that you can define in and

Cone-shaped weld access hole with radiuses that you can define in and

Capital R defines the large radius (height).

Small r defines the small radius.

R = 35

r = 10

Beam end preparation

Option

Description

Default

Top and bottom flange are prepared.

AutoDefaults can change this option.

Automatic

Top and bottom flange are prepared.

Beam end is not prepared.

Top and bottom flange are prepared.

Top flange is prepared.

Bottom flange is prepared.

Flange cut

Option for top flange

Option for bottom flange

Description

Default

Flange is not cut.

AutoDefaults can change this option.

Flange is not cut.

Flange is cut.

Weld backing bars

Option for top backing bar

Option for bottom backing bar

Description

Default

Backing bars are created inside the flanges.

AutoDefaults can change this option.

No backing bars are created.

Backing bars are created inside the flanges.

Backing bars are created outside the flanges.

Weld backing bar length

Enter the length of the weld backing bar in the box below the options.

Option

Description

Default

Absolute length of the backing bar

AutoDefaults can change this option.

Absolute length of the backing bar

Extension beyond the edge of the flange

Weld backing bar position

Option

Description

Enter a positive or a negative value to move the front end of the backing bar relative to the end of the flange.

Assembly type

Define the location where the weld backing bar welds are made. When you select the Workshop option, Tekla Structures includes the backing bars in the assembly.

General tab

Click the link below to find out more:

General tab

Analysis tab

Click the link below to find out more:

Analysis tab

Submit

Table of Contents