Two side clip angle (33) connects two beams to a beam or to a column web with clip angles. Web extension plates can be created.
Objects created
-
Clip angles
-
Web extension plates
-
Bolts
-
Welds
Use for
| Situation | Description |
|---|---|
|
|
Beams connected to a column with clip angles. |
Selection order
-
Select the main part.
-
Select the first secondary part.
-
Select the second secondary part.
-
Click the middle mouse button to create the connection.
Note that the first secondary part has priority in the common values. For example, if the beams are not at the same elevation, the connection will move the holes in the second secondary to line up with the first secondary holes. The connection will move the holes in the second secondary up or down the minimum required distance so that the holes line up.
Part identification key

| Description | |
|---|---|
|
1 |
Clip angle |
Picture tab
Use the Picture tab to define the connection dimensions.
Dimensions

| Description | |
|---|---|
|
1 |
Secondary part edge distance from the main part web |
|
2 |
Secondary part edge distance from the main part flange |
|
3 |
Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. |
|
4 |
Clip angle edge distance from the main part web |
Parts tab
Use the Parts tab to define the part properties.
Parts
| Option | Description |
|---|---|
|
(1) NS profile (1) FS profile (2) NS profile (2) FS profile |
Select the profile from the profile catalog. |
|
Top Web Ext1 Btm Web Ext1 Top Web Ext2 Btm Web Ext2 |
Thickness, width, and height of the extension plate |
|
Option |
Description |
Default |
|---|---|---|
|
Pos_No |
Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number. |
The default part start number is defined in the Components settings in . |
|
Material |
Material grade. |
The default material is defined in the Part material box in the Components settings in . |
|
Name |
Name that is shown in drawings and reports. |
|
|
Finish |
Describes how the part surface has been treated. |
Parameters tab
Use the Parameters tab to define the beam cut, clip angle orientation and side, and safety connection.
Beam end cut
| Option | Option | Description |
|---|---|---|
|
|
|
Default Tekla Structures determines based on the connection geometry how the beam end is cut. AutoDefaults can change this option. |
|
|
|
Tekla Structures determines based on the connection geometry how the beam end is cut. Automatic |
|
|
|
Bevel cut is created. |
|
|
|
Square cut is created. |
Clip angle creation
Select whether two clip angles, or clip angles on the near or far side are created.
| Option | Option |
|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
Clip angle offset
Define the clip angle offset from the beam centerline.

Extension plate creation
| Option | Description |
|---|---|
|
|
Default Extension plates are created. AutoDefaults can change this option. |
|
|
Extension plates are created. Automatic |
|
|
Extension plates are not created. |
|
|
Extension plates are created. |
Safety connection location
Select the location of the safety connection.

Bolts tab
Use the Bolts tab to define the bolt group dimensions and bolt properties.
Bolt group dimensions

| Description | |
|---|---|
|
1 |
Number of bolts. |
|
2 |
Number of bolts. |
|
3 |
Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. |

| Description | |
|---|---|
|
1 |
Number of bolts. |
|
2 |
Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. |
|
3 |
Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. |
|
4 |
Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. |
|
5 |
Location where the bolts should be attached. |
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
Bolt assembly
The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.
If you want to create a hole only, clear all the check boxes.
To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.
Bolt length increase
Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.
Slotted holes
You can define slotted, oversized, or tapped holes.

| Option | Description | Default |
|---|---|---|
|
1 |
Vertical dimension of slotted hole |
0, which results in a round hole. |
|
2 |
Horizontal dimension of slotted hole, or allowance for oversized holes. |
0, which results in a round hole. |
|
Hole type |
Slotted creates slotted holes. Oversized creates oversized holes. No hole does not create holes. Tapped creates tapped holes. |
|
|
Rotate slots |
When the hole type is Slotted, this option rotates the slotted holes. |
Staggering of bolts
| Option | Description |
|---|---|
|
|
Select how the bolts are staggered. |
Copes 2/Copes 3 tab
Use the Copes tabs to create notches in the secondary beams and to control the notch shape and dimensions, and the minimum cope clearance. The images below are from the Copes 2 tab.
Notch shape
| Option | Description |
|---|---|
|
|
Select the notch shape. |
Notch side
| Option | Description |
|---|---|
|
|
Default Notches are created on both sides. AutoDefaults can change this option. |
|
|
Notches are created on both sides. |
|
|
Notch is created on the left side. |
|
|
Notches are created on both sides. |
|
|
Notch is created on the right side. |
Chamfered notch
| Option | Description |
|---|---|
|
|
Define the length of the narrow part of the chamfered notch. |
Notch dimensions

| Description | |
|---|---|
|
1 |
Vertical notch dimension |
|
2 |
Horizontal notch dimension |
More tab
Use the More tab to define the clip angle orientation.
Clip angle orientation
Select how the clip angles are oriented: longer legs horizontal, or vertical on the far or near side.
The options below are for the first secondary part. The second secondary part has the corresponding options.
| Option |
|---|
|
|
|
|
|
|
|
|
General tab
Click the link below to find out more:
Design tab
Click the link below to find out more:
Analysis tab
Click the link below to find out more:
Welds
Click the link below to find out more:
































