Simple base plate (55) connects a beam to a column or another beam using a base plate.
Objects created
-
Base plate
-
Stiffeners (for W profiles only)
-
Bolts
-
Welds
Use for
| Situation | Description |
|---|---|
|
|
Base plate created between column end and beam |
Selection order
-
Select the main part (column or beam).
-
Select the secondary part (beam or column).
The connection is created automatically when the secondary part is selected.
Part identification key

| Description | |
|---|---|
|
1 |
Base plate |
|
2 |
Stiffeners |
Picture tab
Use the Picture tab to define the plate position and corner cuts.
Dimensions

| Description | |
|---|---|
|
1 |
Base plate offset from the bottom edge of the secondary part. |
|
2 |
Distance from the main part to the base plate bottom. |
Base plate corner cut

| Description | |
|---|---|
|
1 |
Horizontal corner cut dimension. |
|
2 |
Vertical corner cut dimension. |
Parts tab
Use the Parts tab to define the plate properties.
Parts
| Option | Description |
|---|---|
|
Base plate |
Thickness, width, and height of the base plate. |
|
Stiffeners |
Thickness, width, and height of the stiffeners. |
|
Option |
Description |
Default |
|---|---|---|
|
Pos_No |
Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number. |
The default part start number is defined in the Components settings in . |
|
Material |
Material grade. |
The default material is defined in the Part material box in the Components settings in . |
|
Name |
Name that is shown in drawings and reports. |
Parameters tab
Use the Parameters tab to define the condensation holes and base plate corner shape.
| Option | Description |
|---|---|
|
Plate wrap around |
Define how the base plate is automatically wrapped:
|
|
Condensation holes sides 1-4 |
Define 1 - 4 condensation holes in the side walls of specific closed profiles, such as hollow sections, box sections, and so on. You can enter any combination using the numbers 1, 2, 3, 4. The up direction of the component determines the placement of the first condensation hole 1 in the profile wall, and the following holes 2 - 4 are placed in a clockwise rotation in the following profile walls. Semi-circular holes are placed at the bottom end of the supported closed hollow profiles. |
|
Condensation holes diameter |
Define the diameter of the condensation holes. |
Base plate corner shape
| Description | |
|---|---|
|
1 |
Define which plate corners are reshaped. You can enter the corner numbers in any order. Corners are not reshaped if you do not enter any numbers. |
|
2 |
Define the horizontal offset of the plate from the bolt center line. This offset works when Plate wrap around is set to Automatic. |
|
3 |
Define the vertical offset of the plate from the bolt center line. This offset works when Plate wrap around is set to Automatic. |
Bolts tab
Use the Bolts tab to control the bolt group dimensions and the bolt properties.
Bolt group dimensions
| Description | |
|---|---|
|
1 |
Select how to measure the dimensions for vertical bolt group position.
|
|
2 |
Dimension for vertical bolt group position. |
|
3 |
Number of bolts. |
|
4 |
Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. |
|
5 |
Select how to measure the dimensions for horizontal bolt group position.
|
|
6 |
Dimension for horizontal bolt group position. |
Bolt group rotation

| Description | |
|---|---|
|
1 |
Define the bolt group rotation around the column center line, measured from the column web. |
Bolt deletion
| Option | Description |
|---|---|
|
Edge tolerance for deleting bolts |
Define the minumum bolt edge distance for deleting bolts. The distance is measured from the bolt center to the edge of the plate. |
|
Eliminate bolts |
Define which bolts are deleted. Enter the bolt numbers from the first bolt in the first row to the last bolt in the last row, for example, 1 3 10. Enter A or a to delete all bolts. |
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
Slotted holes
You can define slotted, oversized, or tapped holes.
|
Option |
Description |
Default |
|---|---|---|
|
1 |
Vertical dimension of slotted hole. |
0, which results in a round hole. |
|
2 |
Horizontal dimension of slotted hole, or allowance for oversized holes. |
0, which results in a round hole. |
|
Hole type |
Slotted creates slotted holes. Oversized creates oversized holes. No hole does not create holes. Tapped creates tapped holes. |
|
|
Rotate Slots |
When the hole type is Slotted, this option rotates the slotted holes. |
|
|
Slots in |
Part(s) in which slotted holes are created. The options depend on the component in question. |
Bolt assembly
The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.
If you want to create a hole only, clear all the check boxes.
To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.
Bolt length increase
Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.
Special holes for bolts
You can create special holes and define the parts in which the special holes are created.
| Option | Description |
|---|---|
|
|
Default Special holes are not created. AutoDefaults can change this option. |
|
|
Special holes are not created. |
|
|
Special holes are created in the part. |
|
|
Special holes are created in the end plate. |
|
|
Special holes are created in both the end plate and the part. |
Stiffeners tab
Use the Stiffeners tab to define the stiffener dimensions and chamfering.
Stiffener offset

| Option | Description |
|---|---|
|
1 |
Stiffener offset from the base plate. |
|
2 |
Stiffener offset from the column or beam. |
Stiffener positions

| Description | |
|---|---|
|
1 |
Stiffener position on the base plate edge. |
|
2 |
Define on which sides the stiffeners are created. |
Chamfer dimensions

| Description | |
|---|---|
|
1 |
Horizontal dimension of the chamfer. |
|
2 |
Vertical dimension of the chamfer. |
Chamfer type
| Option | Description |
|---|---|
|
|
Default No chamfer AutoDefaults can change this option. |
|
|
Line chamfer |
|
|
Convex chamfer |
|
|
Concave chamfer |
|
|
No chamfer |
General tab
Click the link below to find out more:
Analysis tab
Click the link below to find out more:
Welds
Click the link below to find out more:










