Wind column (5) connects a rafter to a wind column by using a single L profile or a twin seat profile. A cap plate is added to the wind column, and a vertical plate on top of the cap plate to be connected to the seat. The seat can be created above or below the rafter, and the wind column is adjusted accordingly. The seat can either be bolted or welded to the rafter and the vertical plate.
Objects created
-
Vertical plate
-
Cap plate
-
L/T seat profile
-
Bolts
-
Welds
Use for
| Situation | Description |
|---|---|
|
|
Rafter connected to a wind column. Plate offset option. |
|
|
Wind column to beam connection. |
Selection order
-
Select the main part (wind column).
-
Select the secondary part (rafter).
The connection is created automatically when the secondary part is selected.
Part identification key

| Description | |
|---|---|
|
1 |
Cap plate |
|
2 |
Vertical plate |
|
3 |
L/T seat profile |
Picture tab
Use the Picture tab to define the connection dimensions.
Dimensions

| Description | |
|---|---|
|
1 |
Distance between the rafter and the seat. |
|
2 |
If the seat is bolted, this dimension is the bolt edge distance of the seat on the rafter side. If the seat is welded, this dimension is the distance from the rafter center line to the edge of the seat. |
|
3 |
Distance from the rafter center to the nearest plate bolt. |
|
4 |
Bolt edge distance. |
|
5 |
Cap plate edge extension in the direction parallel to the seat. |
|
6 |
Distance between the vertical plate and the seat. |
|
7 |
Distance between the column center line and the vertical plate. |
|
8 |
Cap plate edge extension in the direction perpendicular to the seat. |
Parts tab
Use the Parts tab to define the part properties.
Parts
| Option | Description |
|---|---|
|
Vertical plate |
Thickness of the vertical plate. |
|
Cap plate |
Thickness of the cap plate. |
|
L/T profile |
Select the profile from the profile catalog. |
|
Option |
Description |
Default |
|---|---|---|
|
Pos_No |
Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number. |
The default part start number is defined in the Components settings in . |
|
Material |
Material grade. |
The default material is defined in the Part material box in the Components settings in . |
|
Name |
Name that is shown in drawings and reports. |
Parameters tab
Use the Parameters tab to define the seat type, orientation, and position.
Seat type
| Option | Description |
|---|---|
|
|
Default Seat at the near side. AutoDefaults can change this option. |
|
|
Seat at the near side. |
|
|
Seat at the far side. |
|
|
Seat at both sides. |
Seat orientation
| Option | Description |
|---|---|
|
|
Default Longer leg is horizontal. AutoDefaults can change this option. |
|
|
Longer leg is horizontal. |
|
|
Longer leg is vertical. |
Seat position
| Option | Description |
|---|---|
|
|
Default Seat is below the rafter. AutoDefaults can change this option. |
|
|
Seat is below the rafter. |
|
|
Seat is above the rafter. |
Plate bolts tab
Use the Plate bolts tab to define the bolt group dimensions, bolt properties, and the vertical plate connection to the seat.
Bolt group dimensions

| Description | |
|---|---|
|
1 |
Number of bolts. |
|
2 |
Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. |
|
3 |
Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. |
|
4 |
Define which bolts are deleted from the bolt group. Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom. |
Connection type
Select how the vertical plate is connected to the seat.
| Option | Description |
|---|---|
|
|
Default Bolted AutoDefaults can change this option. |
|
|
Bolted |
|
|
Welded |
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
Slotted holes
You can define slotted, oversized, or tapped holes.
|
Option |
Description |
Default |
|---|---|---|
|
1 |
Vertical dimension of slotted hole. |
0, which results in a round hole. |
|
2 |
Horizontal dimension of slotted hole, or allowance for oversized holes. |
0, which results in a round hole. |
|
Hole type |
Slotted creates slotted holes. Oversized creates oversized holes. No hole does not create holes. Tapped creates tapped holes. |
|
|
Rotate Slots |
When the hole type is Slotted, this option rotates the slotted holes. |
|
|
Slots in |
Part(s) in which slotted holes are created. The options depend on the component in question. |
Bolt assembly
The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.
If you want to create a hole only, clear all the check boxes.
To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.
Bolt length increase
Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.
Beam bolts
Use the Beam bolts tab to define the bolt group dimensions, bolt properties, and the rafter connection to the seat.
Bolt group dimensions

| Description | |
|---|---|
|
1 |
Distance between the rafter center and the bolts. |
|
2 |
Number of bolts. |
|
3 |
Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. |
|
4 |
Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. |
Connection type
Select how the rafter is connected to the seat.
| Option | Description |
|---|---|
|
|
Default Bolted AutoDefaults can change this option. |
|
|
Bolted |
|
|
Welded |
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
General tab
Click the link below to find out more:
Design tab
Click the link below to find out more:
Analysis tab
Click the link below to find out more:
Welds
Click the link below to find out more:

















