Skip to main content

CMF Window Trimmer Rail (37) - Parameters tab

Tekla Structures - Not version-specific
Not version-specific
Tekla Structures
Environment
Not environment-specific

Use the Parameters tab in the CMF Window Trimmer Rail Properties panel to control how the connecting members are defined within Tekla Structures.

Image
tekla-structures-cmf-37-parameters-tab.png

 

OptionDescriptionDefaultOther
Profile Type
(Multiple choice)
This defines the strut type to be used between the selected rails. If set to Default the profile will be CMF-C12315.The default is set to Default. 
Face Strut to the
(Left, Right)
This controls the direction of the strut created. If this is set to Left then looking from the first rail selected to the second, the rail support will be orientated so that the strut faces to the left. The Right option similarly causes the rail support to face to the right.The default is set to Right.
Image
tekla-structures-parameters-tab-face-strut-to-the-left.png
Left
Image
tekla-structures-parameters-tab-face-strut-to-the-right.png
Right
Start at the (Top, Bottom)This defines the direction of the strut, either top down or bottom up. This is useful when you want to change the sheeting face used by the macro.The default is set to Bottom. 
Top_Cleat_Type
(No Cleat, Trimmer Cleat)
This is a simple option to define whether or not to put a cleat at the top of the strut.The default is set to Trimmer Cleat. 
Top Cleat Side
(Outside, Inside, Default)
This defines a location of the cleat, either the inside or outside of the strut.The default is set to Default. 
Btm_Cleat_Type
(No Cleat, Trimmer Cleat)
This is a simple option to define whether or not to put a cleat at the bottom of the strut.The default is set to Trimmer Cleat. 
Bottom Cleat Side
(Outside, Inside, Default)
This defines a location of the cleat, either the inside or outside of the strut.The default is set to Default. 
Top Cleat Bolt GradeThis sets the bolt standard for the strut connecting to the last rail.The default setting is 8.8XOX. 
Bottom Cleat Bolt GradeThis sets the bolt standard for the strut connecting to the first rail.The default setting is 8.8XOX. 
GroupThis sets the class that all parts will be included in.The default setting is 99. 
Btm Cleat Edge DistThis specifies the distance between the centre of the bolt and the edge on both sides of the bottom cleat, this will alter the length of the cleat.This value will come from the data files.
Image
tekla-structures-parameters-tab-btm-cleat-edge-dist.png
Top Cleat Edge DistThis specifies the distance between the centre of the bolt and the edge on both sides of the top cleat, this will alter the length of the cleat.This value will come from the data files.See above.
Btm Cleat Bolt CentersThis controls the hole centres for the slotted holes in the bottom cleat.This value will come from the data files. 
Top Cleat Bolt CentersThis controls the hole centres for the slotted holes in the top cleat.This value will come from the data files. 
Btm Strut Vertical OffsetThis defines the gap between the back of the bottom cleat and the bottom of the strut.This value will come from the data files.
Image
tekla-structures-parameters-tab-btm-strut-vertical-offset.png
Top Strut Vertical OffsetThis defines the gap between the back of the top cleat and the top of the strut.This value will come from the data files.See above.
Btm Cleat BackMarkThis specifies the distance from the bolt to the back of the bottom cleat.This value will come from the data files. 
Top Cleat BackMarkThis specifies the distance from the bolt to the back of the top cleat.This value will come from the data files. 
Sheeting Line DistThis specifies an offset distance for the strut member. Postive numbers are towards the sheeting line.The default distance will be determined appropriately from the model data. 

See also

CMF cold rolled - Important information
CMF Window Trimmer Rail (37)
CMF Window Trimmer Rail (37) - Parts tab
Submit