Skip to main content

Stringer stanchion L profile (68)

Modified: 10 Dec 2024 Tekla Structures 2026
2026
Tekla Structures

Stringer stanchion L profile (68) creates a connection between a stair stringer and a handrail stanchion. The connection includes a clip angle and either welded or bolted connections. You can define which parts are to be welded or bolted.

Objects created

  • Clip angle

  • Bolts

  • Welds

Use for

Situation Description

Stringer connected to a stanchion with a clip angle.

Selection order

  1. Select the main part (stringer).

  2. Select the secondary part (stanchion).

    The connection is created automatically when the secondary part is selected.

Part identification key

Description

1

Clip angle

Picture tab

Use the Picture tab to define the connection dimensions.

Dimensions

Description

1

Distance from the intersection of the centerline of the stanchion and the top edge of the stringer down to the top edge of the clip angle.

2

Distance from the top edge of the clip angle to the cut end of the handrail stanchion.

3

Distance from the bottom edge of the stanchion to the intersection of the centerline of the stanchion and the top edge of the stringer.

4

Distance from the bottom edge of the clip angle to the cut end of the handrail stanchion.

5

Distance from the bottom edge of the clip angle to the intersection of the centerline of the stanchion and the bottom edge of the stringer.

6

Distance from the bottom edge of the stanchion to the bottom edge of the clip angle.

7

Distance from the centerline of the stanchion to the edge of the clip angle along the stringer.

Parts tab

Use the Parts tab to define the part properties.

Parts

Option

Description

Profile

Thickness, width, and length of the clip angle.

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

Class

Part class number.

Parameters tab

Use the Parameters tab to define the stanchion position, clip angle leg direction, attachment type, clip angle orientation, stanchion cut, clip angle orientation in skewed situations, and chamfer dimensions and type.

Stanchion position

Option

Description

Default

Stanchion is created to the left side of the clip angle.

AutoDefaults can change this option.

Stanchion is created to the left side of the shear tab.

Stanchion is created on the centerline of the outstanding leg of the clip angle.

Stanchion is created to the right side of the clip angle.

Clip angle leg direction

Option

Description

Default

Clip angle is attached to the stringer with the attached leg to the right side of the stanchion.

AutoDefaults can change this option.

Clip angle is attached to the stringer with the attached leg to the right side of the stanchion.

Clip angle is attached to the stringer with the attached leg to the left side of the stanchion.

Attachment type

Option

Description

Default

Stanchion is welded to the clip angle and the clip angle is bolted to the stringer.

AutoDefaults can change this option.

Stanchion is bolted to the clip angle and the clip angle is bolted to the stringer.

Stanchion is welded to the clip angle and the clip angle is bolted to the stringer.

Stanchion is bolted to the clip angle and the clip angle is welded to the stringer.

Stanchion is welded to the clip angle and the clip angle is welded to the stringer.

Clip angle orientation

Option

Description

Default

Longer leg of the clip angle is vertical.

AutoDefaults can change this option.

Longer leg of the clip angle is vertical.

Longer leg of the clip angle is horizontal.

Stanchion cut

Option

Description

Default

Stanchion is cut according to the value defined on the Picture tab.

AutoDefaults can change this option.

Stanchion is cut according to the value defined on the Picture tab.

Stanchion is not cut.

Clip angle orientation in skewed situations

Option

Description

Default

Clip angle is perpendicular to the stanchion.

AutoDefaults can change this option.

Clip angle is perpendicular to the stanchion.

Clip angle is oriented to the stringer.

Chamfer dimensions and type

Description

1

Horizontal chamfer dimension

2

Vertical chamfer dimension

3

Select the clip angle chamfer type:

  • Default

  • No for no chamfer.

  • Line for line type chamfer.

  • Arc 1 for convex arc chamfer.

  • Arc 2 for concave arc chamfer.

Bolts tab

Use the Bolts tab to control the bolt group dimensions and the bolt properties.

Bolt group dimensions

Description

1

Dimension for vertical bolt group position.

2

Select how to measure the dimensions for vertical bolt group position.

  • Top: From the upper edge of the secondary part to the uppermost bolt.

  • Middle: From the center line of the bolts to the center line of the secondary part.

  • Below: From the lower edge of the secondary part to the lowest bolt.

3

Bolt edge distance.

Edge distance is the distance from the center of a bolt to the edge of the part.

4

Number of bolts.

5

Bolt spacing.

Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.

6

Define which bolts are deleted from the bolt group.

Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom.

Bolt basic properties

Option

Description

Default

Bolt size

Bolt diameter.

Available sizes are defined in the bolt assembly catalog.

Bolt standard

Bolt standard to be used inside the component.

Available standards are defined in the bolt assembly catalog.

Tolerance

Gap between the bolt and the hole.

Thread in mat

Defines whether the thread may be within the bolted parts when bolts are used with a shaft.

This has no effect when full-threaded bolts are used.

Yes

Site/Workshop

Location where the bolts should be attached.

Site

Slotted holes

You can define slotted, oversized, or tapped holes.

Option

Description

Default

1

Vertical dimension of slotted hole.

0, which results in a round hole.

2

Horizontal dimension of slotted hole, or allowance for oversized holes.

0, which results in a round hole.

Hole type

Slotted creates slotted holes.

Oversized creates oversized holes.

No hole does not create holes.

Tapped creates tapped holes.

Rotate Slots

When the hole type is Slotted, this option rotates the slotted holes.

Slots in

Part(s) in which slotted holes are created. The options depend on the component in question.

Bolt assembly

The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.

If you want to create a hole only, clear all the check boxes.

To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.

Bolt length increase

Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.

Sbolts tab

Use the SBolts tab to define the properties of the bolts that connect the clip angle to the stanchion.

Bolt group dimensions

Description

1

Bolt edge distance.

Edge distance is the distance from the center of a bolt to the edge of the part.

2

Number of bolts.

3

Bolt spacing.

Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.

4

Define which bolts are deleted from the bolt group.

Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom.

Bolt basic properties

Option

Description

Default

Bolt size

Bolt diameter.

Available sizes are defined in the bolt assembly catalog.

Bolt standard

Bolt standard to be used inside the component.

Available standards are defined in the bolt assembly catalog.

Tolerance

Gap between the bolt and the hole.

Thread in mat

Defines whether the thread may be within the bolted parts when bolts are used with a shaft.

This has no effect when full-threaded bolts are used.

Yes

Site/Workshop

Location where the bolts should be attached.

Site

Slotted holes

You can define slotted, oversized, or tapped holes.

Option

Description

Default

1

Vertical dimension of slotted hole.

0, which results in a round hole.

2

Horizontal dimension of slotted hole, or allowance for oversized holes.

0, which results in a round hole.

Hole type

Slotted creates slotted holes.

Oversized creates oversized holes.

No hole does not create holes.

Tapped creates tapped holes.

Rotate Slots

When the hole type is Slotted, this option rotates the slotted holes.

Slots in

Part(s) in which slotted holes are created. The options depend on the component in question.

Bolt assembly

The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.

If you want to create a hole only, clear all the check boxes.

To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.

Bolt length increase

Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.

General tab

Click the link below to find out more:

General tab

Design tab

Click the link below to find out more:

Design tab

Analysis tab

Click the link below to find out more:

Analysis tab

Submit

Table of Contents