Footplate (1029)
System component Footplate (1029) can be used to create a base plate to a column end.
Objects created
- Base plate
- Shim plates (optional)
- Leveling plate (optional)
- Shear key (optional)
- Extra plates connecting the anchor rods
- Anchors
- Bolts
- Additional component (optional)
- Welds
Use for
| Situation | Description |
|---|---|
|
Image
| Simple base plate detail |
|
Image
| Base plate detail with stiffeners |
|
Image
| Base plate detail with
|
|
Image
| Base plate detail for a concrete column with recesses. |
Before you start
Create a column.
Back to topSelection order
1. Select the main part (column).
2. Pick a position (=bottom base plate)
The base plate detail is created automatically.
Part identification key
| Option | Description |
|---|---|
| 1 | Base plate |
| 2 | Shim plate (optional) |
| 3 | Stiffeners (optional) |
| 4 | Cast plate (optional) |
| 5 | Anchors (optional) |
| 6 | Anchor plate (optional) |
Picture tab
Use the Picture tab to control the offset of the main parts.
| Option | Description | |
|---|---|---|
| 1 | Define the distance from the flange to the edge of the base plate. Enter a negative value to make the base plate larger. | |
| 2 | Define the height of the additional beam. NOTE: The additional beam is only created when a profile is defined in the Parts tab. | |
| 3 | Set the stiffeners offset from the column edge. NOTE: Only applies if the stiffeners are created in the Stiffeners tab. | |
| 4 | Set the additional beam horizontal offset from the column center. | |
| 5 | Set the additional beam vertical offset from the column center. | |
| 6 | Select the placing of base plate. This most importantly implies aligning slanted columns. The options are:
| |
Parts tab
Use the Parts tab to control the dimensions of the base plate, shear key, leveling plate, shim plate and their placing.
| Option | Description | |||
|---|---|---|---|---|
| Plate | Define the thickness, width, and height of the base plate. Position number, material and name can also be defined. If the width and height fields are left empty, the dimensions are set by the defined bolt spacing and edge distance. | |||
| Web plates | Define the thickness of the stiffeners parallel to the column web. The default value is 10. Position number, material and name can also be defined. The placing of the web plates depends on the settings used in the Stiffeners tab. | |||
| Flange plates 4 pcs | Define the thickness of the stiffeners parallel to the column flange. The default value is Position number, material and name can also be defined. The placing of the flange plates depends on the settings used in the Stiffeners tab. Image
| |||
| Additional beam | Create additional beam by selecting a profile from the catalog. Position number, material and name can also be defined. Select the rotation of the additional beam. The options are:
Set to which part the additional beam should be welded. The options are:
| |||
| Leveling plate | Define the thickness, width, and height of the leveling plate. Position number, material and name can also be defined. If the width and height fields are left empty, the leveling plates will have the same dimensions as the base plate. | |||
| Fitting Plate 1 Fitting Plate 2 Fitting Plate 3 | Define the thickness, width and height of the fitting plate. Various thicknesses can be defined for each fitting plate: Image
Position number, material and name can also be defined. | |||
| Horizontal plates | Define the thickness of the plates which can be welded parallel to both flanges. Position number, material and name can also be defined. Image
Image
| |||
| L-profile, flange | Select the L-profile on flange side of the column. L-profile can be welded to both horizontal flange plates. Image
| |||
| L-profile, web | Select the L-profile on web side of the column. L-profile can be welded to both web plates. The L-profiles are only created when the following option is set in the Stiffeners tab: Image
| |||
| Number of fitting plates 1 (DEF=1) Number of fitting plates 2 (DEF=1) Number of fitting plates 3 (DEF=1) | Enter a value to define the number of fitting plates. If a field is left empty, 1 fitting plate will be created (DEF=1). | |||
| Plate offset X | Offset of the leveling plate in the x-direction. | |||
| Plate offset Y | Offset of the leveling plate in the y-direction. | |||
| Chamfer settings | Decide whether all chamfers should be equal or not. The options are:
When option "Same all sides" is used, the option on the top left hand side rules. | |||
| 1 | Select the corner chamfer shape. The upper left corner is used standard for the other corners. The options are: Image
| |||
| 2 | Define the chamfer dimensions in x- and y-direction. Image
| |||
| 3 | Select the shim plate shape. | |||
|
Image
| Default Holes are based on the bolt group of the detail. AutoDefaults can change this option. |
Image
| Finger shim plate with vertical slots. The plate can be installed from the top of the detail. | |
|
Image
| Holes are based on the bolt group of the detail. |
Image
| Halved shim plates in vertical direction. Use the value field to define the gap size. | |
|
Image
| Finger shim plate with horizontal slots. The plate can be installed from the right or left side of the detail. |
Image
| Halved shim plates in horizontal direction. Use the value field to define the gap size. | |
| 4 | Define horizontal and vertical bold edge distances in the shim plates. Edge distance is the distance from the center of a bolt to the edge of the part. If these fields are left empty, the shim plates will have the same dimensions as the base plate. | |||
Stiffeners tab
Use the Stiffeners tab to control if stiffeners are created at the bottom side of the column. Also dimensions of the stiffeners are defined.
| Option | Description | |||
|---|---|---|---|---|
| 1 | Set the stiffeners and their dimensions on the flange side. | |||
| 2 | Define the stiffeners height. | |||
| 3 | Define the stiffeners corner chamfer in horizontal direction. | |||
| 4 | Define the stiffeners corner chamfer in vertical direction. | |||
| 5 | Define the stiffeners width. | |||
| 6 | Choose the corner chamfer type. The options are: Image
| |||
| 7 | Choose the stiffeners type. The options are: | |||
|
Image
| Standard AutoDefaults can change this option. |
Image
| Four stiffeners parallel to the web. | |
|
Image
| No stiffeners. |
Image
| Two plates + L-profiles parallel to the flanges. | |
|
Image
| Two stiffeners parallel and aligned to the web. |
Image
| One stiffener above and parallel to the web. | |
|
Image
| Two stiffeners parallel to the web and placed next to the flanges. |
Image
| One stiffener below and parallel to the web. | |
| 8 | Set the stiffeners and their dimensions on the web side. | |||
| 9 | Choose the stiffeners type. The options are: | |||
|
Image
| Standard AutoDefaults can change this option. |
Image
| Two stiffeners parallel to the flanges. | |
|
Image
| No stiffeners. |
Image
| Two stiffeners + L-profiles parallel to the web. | |
|
Image
| Four stiffeners parallel to the flanges. | |||
| Set the dimension for stiffeners along the flange sides and for the L-profiles. | ||||
| 10 | ||||
| 11 | Define stiffeners height. | |||
| 12 | Define stiffeners width. | |||
| 13 | Define the length of the L-profile parallel to the flanges. | |||
| 14 | Define the length of the L-profile parallel to the web. | |||
General tab
Click the link below to find out more:
General tab
Bolts tab
Use the Bolts tab to control the bolt properties. If anchors are used instead of bolts, the fields for bolt rows, spacing and edge distance remain active.
| Option | Description | |
|---|---|---|
| Bolt size | Define the bolt diameter. The default value is 16 mm. | |
| Standard | Define the bolt assembly standard/grade. The default value is 4014-8.8. | |
| Tolerance | Define the tolerance = Hole diameter - Bolt diameter. The default value is 4 mm. | |
| Thread in material | Indicate if the thread of the bolt can be inside the bolted parts. The options are:
Tekla Structures does not use this value when calculating the length of full-threaded bolts. | |
| Bolt type | Define whether the bolts are assembled on-site or in the workshop. The options are:
| |
| 1 | Define slotted hole dimensions in x- and y-direction. These fields can also be used to set the tolerance of oversized and tapped holes. Image
Setting standard | |
| Hole type | Select hole type. The options are:
| |
| Rotate Slots | Choose how the slots should be rotated. The options are:
If the hole type is set to slotted, this option can be used to set the rotation of the slotted holes: Image
| |
| 2 | Select whether to create washers and nuts with the bolt. Image
The option Effect in modify enables the bolt assembly to be modified in existing components when the existing component is modified. | |
| 3 | Define additional bolt length. Additional bolt length increases the material thickness that Tekla Structures uses when calculating bolt length. For example, you might need extra bolt length to allow for painting. You can also build additional lengths into bolt assemblies. Image
| |
| 4 | Set the bolt group rotation. This option is available when on the Anchors tab the option Base plate with is set to Bolts or Bolts and custom part. | |
|
Image
| Standard Bolt direction 1 AutoDefaults can change this option. | |
|
Image
| Bolt direction 1 | |
|
Image
| Bolt direction 2 | |
| Cut length | Indicate which parts the bolt connects. The value defines the area Tekla Structures should search for parts that belong to the bolt group. Using cut length you can determine whether the bolt will go through one flange or two. | |
| Bolt Comment | Add bolt comment. | |
| 5 | Select how to measure the dimensions for horizontal bolt group position. The options are:
Image
Image
Image
| |
| 6 | Define dimension for horizontal bolt group position. | |
| 7 | Define bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. | |
| 8 | Define number of bolts. | |
| 9 | Define bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. | |
| 10 | Select how to measure the dimensions for vertical bolt group position. The options are:
Image
Image
Image
| |
| 11 | Define dimension for vertical bolt group position. | |
| 12 | Define which bolts are deleted from the bolt group. Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom. | |
Anchor rods tab
Use the Anchor rods tab to control the creation of different types of anchor rods.
| Option | Description | |||
|---|---|---|---|---|
| Rod profile | Choose anchor rod profile. The pos-prefix, assembly-prefix, start number, material, name, class, comment and finish can also be defined. | |||
| Cast plate | Define cast plate thickness, width and height. The pos-prefix, assembly-prefix, start number, material, name, class, comment and finish can also be defined. If a cast plate is used with nail holes, it is better to leave the width and height fields of cast plate blank in the "Anchor rods" tab and let the cast plate size be derived from the values defined in the "Nail holes" tab. Image
Image
| |||
| Base plate with | Choose with what the base plate should be created. The options are:
| |||
Bolts Image
| ||||
Anchor rods Image
| ||||
In the options Custom part, Bolts and custom part, Anchors with custom component part a custom component of the type Part can be used. Image
| ||||
| Reference Point | Select the reference point. The options are:
| |||
| Part name component | Select the custom component of the type Part and the used component setting. | |||
| Mirror | Option to mirror the custom component. | |||
| Add as subassembly | Decide, whether the custom part should be added as subassembly. Option:
| |||
No
| The custom component of the type Part (e.g. Anchor rod caps) are not added, but are loose parts (to transport). Image
| |||
| To cast plate | The custom components of the type Part (e.g. Anchor rod caps) are added as subassembly to the cast plate. Image
| |||
| To foot plate | The custom components of the type Part (e.g. Anchor rod caps) are added as subassembly to the foot plate. Image
| |||
| 1 | Define nut height. As a default value the anchor diameter is applied. | |||
| 2 | Define washer thickness. As a default value half the nut height is applied. | |||
| 3 | Anchor length above the base plate. As a default value | |||
| 4 | Distance between cast plate and base plate. As a default value | |||
| 5 | Define length of the upper thread. | |||
| 6 | Define anchor length. As a default value | |||
| 7 | Select the anchor rod types. | |||
|
Image
| Standard AutoDefaults can change this option. | |||
|
Image
| Straight anchor rods. | |||
|
Image
| Anchor rods 90 degrees. The anchor length is counted from the bottom line of the anchor rods. | |||
|
Image
| Anchor rods 180 degrees (height bended part defined from rod bottom) | |||
|
Image
| Straight anchor rods + extra plate at the bottom | |||
|
Image
| Anchor rods 90 degrees. The anchor length is counted from the centerline of the anchor rods. | |||
|
Image
| Anchor rods 180 degrees (height bended part defined from rod centerline) | |||
| 8 | Define hook radius. | |||
| 9 | Define hook width. | |||
| 10 | Define hook height. | |||
| 11 | Define length beneath extra plate. | |||
| 12 | Define length of threaded rod on bottom side anchor. | |||
| 13 | Choose the hook direction. It only effects anchor rods when hook anchors are applied. The following options are available: | |||
|
Image
| Standard Type 1 AutoDefaults can change this option. |
Image
| Parallel to the flanges, outwards. | |
|
Image
| Parallel to the web, outwards. |
Image
| Parallel to the flanges, inwards. | |
|
Image
| Parallel to the web, inwards. | |||
| 14 | Activate the selection boxes to define if the anchor nuts, washer and extra plates are created. | |||
| 15 | Activate the selection boxes to define if the anchor nuts, washers and extra plates are welded to the anchor rod. | |||
| Cast plate holes tolerance | Extra tolerance for the cast plate holes and base plate for the anchor rods. As a default value | |||
| Weldings of anchorbar | Decide, to which part the anchorbar is welded. The options are:
| |||
| Use weld number | A specific weld can be selected to weld the anchorbar. The options are:
| |||
| Apply rods finish | Here you can indicate whether the finish of the anchors also applies to the rods, nuts, and washers. The options are:
| |||
Hidden UDA's
Certain parts receive certain variables, which are written by the component. These are used in the list "anchor list.doc" but also in the anchor plan settings of general arrangement drawings. In addition, single-part drawing setting "anchor" and assembly drawings setting "stelmal".
Tip: use the Model Template "Anchor plan".
After using the command Inquire object, the following variables appear, depending on the part from which the information is requested.
| Inquire object | Variable | Description |
|---|---|---|
| Anchors | ANCHOR_A | Radius hook anchor |
| Anchors | ANCHOR_B | Anchor width |
| Anchors, Footplate, Castplate | ANCHOR_H | Height anchor. The calculated length is always to the midelle of the anchor. Independent on the option you have choosen. |
| Anchors, Footplate, Castplate | BPLATE | Thickness of the footplate |
| Anchors, Footplate, Castplate | CPLATE | Thickness of the castplate |
| Anchors, Footplate, Castplate | ANCHOR_TYPE | Anchor type Image
|
| Anchors, Footplate, Castplate | SPACE_A | Distance from the anchors to the top of the footplate |
| Anchors, Footplate, Castplate | SPACE_B | Distance bottom side footplate - bottom side castplate |
| Footplate, Castplate | BPLATE_BLEV | Bottom side footplate |
| Footplate, Castplate | CPLATE_TLEV | Top side castplate |
| Nut | NUT | Position number of the nut, so where is this nut in the height direction. The top one is number 1. Image
|
Calculating with the variables
Next you can use the values, for example in the anchor list. You open the list in Template Editor and add a value field (or edit an existing value field), next use a formula:
Next when you generate the anchor list, the value (which is the result of the formula) is shown (50 + 50 + 10 - 10):
Nuts and washers tab
Use the Nuts and washers tab to define nuts and washer properties.
| Option | Description |
|---|---|
| Nut profile | Select nut profile. The pos-prefix, assembly-prefix, start number, material, name, class and comment can also be defined. |
| Washer profile | Select washer profile. ¨ The pos-prefix, assembly-prefix, start number, material, name, class and comment can also be defined. |
| Plate washer | Define plate washer thickness, width and height. The pos-prefix, assembly-prefix, start number, material, name, class and comment can also be defined. |
| Nut 3 height | Define the height of the nut 3. Check the picture on the tab to identify the nut 3. |
| Nut 4 height | Define the height of the nut 4. Check the picture on the tab to identify the nut 4. |
| Washer 2 height / length | Define the height of the washer 2. To create the washer 2, define also the washer 2 diameter. Check the picture on the tab to identify the nut 2. |
| Washer 2 diameter | Define the diameter of the washer 2. |
| Plate washer holes tolerance | Define extra hole tolerance between anchor rod and washer hole.
if a washer profile without a hole (e.g. D30 profile) is used, no washer hole can be applied. |
| Create hole in washer | Decide, whether the hole in the washer should be created. The options are:
|
| Create hole in nut | Decide, whether the hole in the nut should be created. The options are:
|
| Washer profile reference line | Decide, how the washer's reference line should be aligned. The options are:
|
Nailholes tab
Use the Nailholes tab to set the nailhole properties and dimensions in the cast plate. Nailholes are used to mount the cast plate to the formwork.
| Option | Description | |||
|---|---|---|---|---|
| Hole size | Define the diameter of the nailhole in the cast plate. | |||
| 1 | Define slotted hole dimensions in x- and y-direction. These fields can also be used to set the tolerance of oversized and tapped holes. If the value 0 is set, round holes are created. | |||
| 2 | Select how to measure the dimensions for horizontal nailhole group position. The options are:
| |||
| 3 | Define dimension for horizontal nailhole group position. | |||
| 4 | Define nailhole edge distance. Edge distance is the distance from the center of a nailhole to the edge of the part. | |||
| 5 | Define number of nailholes. | |||
| 6 | Define nailhole spacing. Use a space to separate nailhole spacing values. Enter a value for each space between nailholes. For example, if there are 3 nailholes, enter 2 values. | |||
| 7 | Select how to measure the dimensions for vertical nailhole group position. The options are:
| |||
| 8 | Define dimension for vertical nailhole group position. | |||
| 9 | Define which nailholes are deleted from the nailhole group. Enter the nailhole numbers of the nailholes to be deleted and separate the numbers with a space. nailhole numbers run from left to right and from top to bottom. | |||
| Cast plate reference point | Define whether the cast plate position is set from the column center or bolt group center. The options are:
| |||
Column center: Image
| Bolt group center: Image
| |||
| Cast plate offset in connection direction | Define the displacement of cast plate in the direction of the component. | |||
| Cast plate offset in Y | Define the displacement of the cast plate in the direction perpendicular to the component direction. | |||
Extra tab
Use the Extra tab to control the placement, rotation, and profile type (extra profile 1 and 2) at the anchor rod bottom side. Extra profile 2 connects the anchor rod rows to each other.
| Option | Description | |
|---|---|---|
| Extra profile 1 | Define the first profile. This profile is placed at the bottom of the anchor rods. The default profile PL10*100 is applied. | |
| Extra profile 2 | Define the second profile. This profile connects the anchor rod rows to each other. | |
| 1 | Select the extra profile 1 type and direction. The following options are available: | |
|
Image
| Standard Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
| 2 | Define the edge distance of extra profile 1 from the anchor rod center. | |
Extra profile 1 Hole tolerance | Define the hole tolerance of the anchor rod through extra profile 1 at the bottom side of the anchor rods. | |
Extra profile 1 Profile rotation | Select the rotation for extra profile 1. The options are:
| |
Extra profile 1 Round plates | Decide, whether the round plates should be created instead of rectangular plates. The options are:
| |
| 3 | Select the extra profile 2 type and direction. The following options are available: | |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
| 4 | Define the edge distance of extra profile 2 from the anchor rod center. | |
| 5 | Select the extra profile 2 direction. There are two options available: parallel to the column web or parallel to the column flanges. | |
|
Image
|
Image
| |
|
Image
|
Image
| |
|
Image
|
Image
| |
| 6 | Define the extra profile 2 extra length, measured from the anchor rod center. | |
| Extra profile 2 rotation | Select the rotation for extra profile 2. The options are:
| |
| Welds of extra profile 2 | Decide whether the extra profile 2 should be welded to another part. The options are:
| |
Grout holes tab
Use the Grout holes tab to control the creation of extra holes in the base plate and/or in the cast plate, for example for galvanizing service holes.
It is also possible to create DUMMY-profiles at the extra hole positions, which can be read in a Total Station.
The extra holes for the base plate and cast plate can be defined separately, the left fields are used for the base plate, and the right fields are used for the cast plate.
| Option | Description |
|---|---|
| Hole size | Define the grout holes diameter. |
| Bolt standard | Define the grout holes bolt standard. |
| Tolerance | Define the grout holes tolerance. |
| Read data from | Decide, whether the data should be read from dialog or data file. |
Grout holes (left side) | Define whether extra holes and/or DUMMY profiles for the Total Station are created in the base plate. The options are:
The DUMMY-profiles have the same dimensions as the extra holes. (It is possible to use dummy profiles in Tekla Structures in order to position anchors using a Total Station, click here for more information.) |
Grout holes (right side) | Define whether extra holes and/or DUMMY profiles for the Total Station are created in the cast plate. The options are:
|
| 1 | Define slotted hole dimensions in x- and y-direction. These fields can also be used to set the tolerance of oversized and tapped holes. If the value 0 is set, round holes are created. |
| 2 | Define the dimension for horizontal grout hole group position. |
| 3 | Define the dimension for vertical grout hole group position. |
| 4 | Define the number of grout holes. |
| 5 | Define the grout hole spacing. Use a space to separate grout hole spacing values. Enter a value for each space between grout holes. For example, if there are 3 grout holes, enter 2 values. |
| 6 | Define the number of grout holes. |
| 7 | Define the grout hole spacing. Use a space to separate grout hole spacing values. Enter a value for each space between grout holes. For example, if there are 3 grout holes, enter 2 values. |
| 8 | Select the grout hole pattern type. The following options are available: Image
|
| Delete | Define which grout holes are deleted from the grout hole group. Enter the grout hole numbers of the grout holes to be deleted and separate the numbers with a space. grout hole numbers run from left to right and from top to bottom. |
| Reference point | Define whether the grout holes group position is set from the column center or bolt group center. The options are:
|
Extra plate tab
Use the Extra plate tab to add extra vertical plates which for example can be used to mount wall panels.
| Option | Description | ||||
|---|---|---|---|---|---|
| Extra plate | Define the extra plate profile. The pos-prefix, start number, material and name can also be defined. | ||||
| 1 | Select the option to create extra plates. It is optional to create one plate or two plates at any given side of the column, these plates can be parallel or perpendicular orientated to each other. It is also possible to create three similar orientated plates. Image
| ||||
|
Image
|
Image
|
Image
|
Image
| ||
|
Image
|
Image
|
Image
|
Image
| ||
|
Image
|
Image
|
Image
|
Image
| ||
|
Image
|
Image
|
Image
|
Image
| ||
| 2 | Define the overlap/offset of the extra plate from the base plate top. | ||||
Concrete tab
Use the Concrete tab to define recesses in case the base plate is created for a concrete column. The recesses can be used to create clearance to mount the bolts or nuts.
| Option | Description | |||
|---|---|---|---|---|
| 1 | Select the option for welding the base plate. The options are:
| |||
| 2 | Select, whether the recesses should be created. | |||
|
Image
| Standard AutoDefaults can change this option. | |||
|
Image
| No recesses. | |||
|
Image
| Create recesses around the anchor rods/bolts. | |||
| 3 | Define the recesses depth. | |||
| 4 | Define the recesses width. | |||
| 5 | Define the recesses height. | |||
Analysis tab
Click the link below to find out more:
Analysis tab
About
In the About tab, general information about the extension and the developer can be found.
All rights reserved. No conclusions can be associated to the representation of the pictures in relation to the operating systems under which Tekla Structures runs.
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc-nd/4.0/ or send a letter to Creative Commons, 444 Castro Street, Suite 900, Mountain View, California, 94041, USA.