Salta al contenuto principale

Footplate (1029)

Tekla Structures - Not version-specific
Not version-specific
Tekla Structures
Environment
Construsoft European
Netherlands

Image
001


System component Footplate (1029) can be used to create a base plate to a column end.  

Back to top

Objects created

  • Base plate
  • Shim plates (optional)
  • Leveling plate (optional)
  • Shear key (optional)
  • Extra plates connecting the anchor rods
  • Anchors
  • Bolts
  • Additional component (optional)
  • Welds
Back to top

Use for

SituationDescription
Image
simpele voetplaat.jpg
Simple base plate detail
Image
voetplaat schotjes.jpg
Base plate detail with stiffeners
Image
voetplaat met ankers.jpg

Base plate detail with

  • Straight anchor rods
  • Cast plate
  • Extra plates connecting the anchor rods
Image
voetplaat betonkolom.jpg
Base plate detail for a concrete column with recesses.
Back to top

Before you start

Create a column.

Back to top

Selection order

1. Select the main part (column).
2. Pick a position (=bottom base plate)
    The base plate detail is created automatically.

Back to top

Part identification key

Image
004

 

OptionDescription
1Base plate
2Shim plate (optional)
3Stiffeners (optional)
4Cast plate (optional)
5Anchors (optional)
6Anchor plate (optional)

Picture tab

Use the Picture tab to control the offset of the main parts.

Image
005

 

OptionDescription
1

Define the distance from the flange to the edge of the base plate. 

Enter a negative value to make the base plate larger.

2

Define the height of the additional beam. 

NOTE: The additional beam is only created when a profile is defined in the Parts tab.

3

Set the stiffeners offset from the column edge. 

NOTE: Only applies if the stiffeners are created in the Stiffeners tab.

4Set the additional beam horizontal offset from the column center.
5Set the additional beam vertical offset from the column center.
 6

Select the placing of base plate. This most importantly implies aligning slanted columns.

The options are:

  • Default - the default option is "Automatic".
  • Automatic - the automatic placing.
  • Centered on column - base plate is centered below the column.

Parts tab

Use the Parts tab to control the dimensions of the base plate, shear key, leveling plate, shim plate and their placing.

Image
006

 

OptionDescription
Plate

Define the thickness, width, and height of the base plate. Position number, material and name can also be defined. 

If the width and height fields are left empty, the dimensions are set by the defined bolt spacing and edge distance. 

Web plates

Define the thickness of the stiffeners parallel to the column web. The default value is 10.

Position number, material and name can also be defined. 

The placing of the web plates depends on the settings used in the Stiffeners tab. 

Flange plates 4 pcs

Define the thickness of the stiffeners parallel to the column flange. The default value is 10.

Position number, material and name can also be defined. 

The placing of the flange plates depends on the settings used in the Stiffeners tab. 
The four flange plates are only created when the following option is set in the Stiffeners tab: 

Image
image044.png
Additional beam

Create additional beam by selecting a profile from the catalog. 

Position number, material and name can also be defined. 

Select the rotation of the additional beam.

The options are:

  • Front
  • Top
  • Back
  • Below

Set to which part the additional beam should be welded.

The options are:

  • Default - the default option is "Plate".
  • Plate
  • Leveling plate
Leveling plate

Define the thickness, width, and height of the leveling plate. Position number, material and name can also be defined. 

If the width and height fields are left empty, the leveling plates will have the same dimensions as the base plate. 

Fitting Plate 1
Fitting Plate 2
Fitting Plate 3

Define the thickness, width and height of the fitting plate. Various thicknesses can be defined for each fitting plate: 

Image
depending_ENU_tab_parts_fitting_plates.jpg

Position number, material and name can also be defined. 
If the width and height fields are left empty, the leveling plates will have the same dimensions as the base plate.

Horizontal plates

Define the thickness of the plates which can be welded parallel to both flanges. 

Position number, material and name can also be defined. 
The horizontal plates are only created when the following option is set in the Stiffeners tab: 

Image
image014.png

  

Image
image042.png
L-profile, flange

Select the L-profile on flange side of the column. 

L-profile can be welded to both horizontal flange plates. 
The L-profiles are only created when the following option is set in the Stiffeners tab: 

Image
image014.png
L-profile, web

Select the L-profile on web side of the column. 

L-profile can be welded to both web plates. 

The L-profiles are only created when the following option is set in the Stiffeners tab: 

Image
image015.png
Number of fitting plates 1 (DEF=1)
Number of fitting plates 2 (DEF=1)
Number of fitting plates 3 (DEF=1)
Enter a value to define the number of fitting plates. If a field is left empty, 1 fitting plate will be created (DEF=1).
Plate offset XOffset of the leveling plate in the x-direction.
Plate offset YOffset of the leveling plate in the y-direction.
Chamfer settings

Decide whether all chamfers should be equal or not. 

The options are:

  • Different each side
  • Same all sides

When option "Same all sides" is used, the option on the top left hand side rules.

1

Select the corner chamfer shape. 

The upper left corner is used standard for the other corners. 

The options are:

Image
image017.png
2

Define the chamfer dimensions in x- and y-direction.

Image
image019.png
3Select the shim plate shape.
Image
image021.png
Default

Holes are based on the bolt group of the detail.

AutoDefaults can change this option.
Image
image022.png
Finger shim plate with vertical slots.

The plate can be installed from the top of the detail.
Image
image023.png
Holes are based on the bolt group of the detail.
Image
image024.png
Halved shim plates in vertical direction.

Use the value field to define the gap size. 
Image
image025.png
Finger shim plate with horizontal slots.

The plate can be installed from the right or left side of the detail.
Image
image026.png
Halved shim plates in horizontal direction.

Use the value field to define the gap size.
4Define horizontal and vertical bold edge distances in the shim plates. Edge distance is the distance from the center of a bolt to the edge of the part.
If these fields are left empty, the shim plates will have the same dimensions as the base plate. 

Stiffeners tab

Use the Stiffeners tab to control if stiffeners are created at the bottom side of the column. Also dimensions of the stiffeners are defined.

Image
007

 

OptionDescription
1Set the stiffeners and their dimensions on the flange side.
2Define the stiffeners height.
3Define the stiffeners corner chamfer in horizontal direction. 
4Define the stiffeners corner chamfer in vertical direction.
5Define the stiffeners width.
6

Choose the corner chamfer type. 

The options are:

Image
image032.png
7

Choose the stiffeners type.

The options are:

Image
image034.png
Standard

AutoDefaults can change this option.
Image
image035.png
Four stiffeners parallel to the web.
Image
image036.png
No stiffeners.
Image
image037.png
Two plates + L-profiles parallel to the flanges. 
Image
image038.png
Two stiffeners parallel and aligned to the web.
Image
image039.png
One stiffener above and parallel to the web. 
Image
image040.png
Two stiffeners parallel to the web and placed next to the flanges. 
Image
image041.png
One stiffener below and parallel to the web.
8Set the stiffeners and their dimensions on the web side.
9

Choose the stiffeners type.

The options are:

Image
image034.png
Standard

AutoDefaults can change this option.
Image
image042.png
Two stiffeners parallel to the flanges.
Image
image036.png
No stiffeners.
Image
image043.png
Two stiffeners + L-profiles parallel to the web.
Image
image044.png
Four stiffeners parallel to the flanges.   
Set the dimension for stiffeners along the flange sides and for the L-profiles.
10
11Define stiffeners height.
12Define stiffeners width. 
13Define the length of the L-profile parallel to the flanges. 
14Define the length of the L-profile parallel to the web. 

General tab

Click the link below to find out more:
General tab

Bolts tab

Use the Bolts tab to control the bolt properties. If anchors are used instead of bolts, the fields for bolt rows, spacing and edge distance remain active.

Image
008


 

OptionDescription
Bolt sizeDefine the bolt diameter. The default value is 16 mm.
StandardDefine the bolt assembly standard/grade. The default value is 4014-8.8.
ToleranceDefine the tolerance = Hole diameter - Bolt diameter. The default value is 4 mm.
Thread in material

Indicate if the thread of the bolt can be inside the bolted parts. 

The options are:

  • Default - the default value is "Yes".
  • No
  • Yes

Tekla Structures does not use this value when calculating the length of full-threaded bolts.

Bolt type

Define whether the bolts are assembled on-site or in the workshop. 

The options are:

  • Default - the default value is "Site".
  • Site
  • Workshop
1

Define slotted hole dimensions in x- and y-direction. These fields can also be used to set the tolerance of oversized and tapped holes.

Image
image053.png

Setting standard 0 mm results in a round hole.

Hole type

Select hole type.

The options are:

  • Default
  • Slotted
  • Oversized
  • No holes - can be used for plates which are screwed.
  • Tapped
Rotate Slots

Choose how the slots should be rotated.

The options are:

  • Default
  • odd
  • even
  • parallel

If the hole type is set to slotted, this option can be used to set the rotation of the slotted holes: 

Image
image054.png
2

Select whether to create washers and nuts with the bolt.
If you want to create only holes without any bolts, clear all the check boxes.

Image
009

The option Effect in modify enables the bolt assembly to be modified in existing components when the existing component is modified. 

3

Define additional bolt length. 

Additional bolt length increases the material thickness that Tekla Structures uses when calculating bolt length. For example, you might need extra bolt length to allow for painting. You can also build additional lengths into bolt assemblies. 

Image
010
4
 

Set the bolt group rotation. 

This option is available when on the Anchors tab the option Base plate with is set to Bolts or Bolts and custom part. 

Image
image050.png
Standard
Bolt direction 1
AutoDefaults can change this option.
Image
image051.png
Bolt direction 1
Image
image052.png
Bolt direction 2
Cut lengthIndicate which parts the bolt connects. The value defines the area Tekla Structures should search for parts that belong to the bolt group. Using cut length you can determine whether the bolt will go through one flange or two.
Bolt CommentAdd bolt comment.
5

Select how to measure the dimensions for horizontal bolt group position.

The options are:

  • Left - from the left edge of the secondary part to the leftmost bolt.
Image
image058.png
  • Middle - from the center line of the secondary part to the center line of the bolts.
Image
image059.png
  • Right - from the right edge of the secondary part to the rightmost bolt. 
Image
image060.png
6Define dimension for horizontal bolt group position.
7Define bolt edge distance.
Edge distance is the distance from the center of a bolt to the edge of the part.
8Define number of bolts.
9Define bolt spacing.
Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.
10

Select how to measure the dimensions for vertical bolt group position.

The options are:

  • Top - from the upper edge of the secondary part to the uppermost bolt.
Image
image067.png
  • Middle - from the center line of the bolts to the center line of the secondary part.
Image
image068.png
  • Below - from the lower edge of the secondary part to the lowest bolt. 
Image
image069.png
11Define dimension for vertical bolt group position.
12Define which bolts are deleted from the bolt group.
Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom.

Anchor rods tab

Use the Anchor rods tab to control the creation of different types of anchor rods.

Image
011

 

OptionDescription
Rod profile

Choose anchor rod profile. 

The pos-prefix, assembly-prefix, start number, material, name, class, comment and finish can also be defined. 

Cast plate

Define cast plate thickness, width and height. 

The pos-prefix, assembly-prefix, start number, material, name, class, comment and finish can also be defined.
 

If a cast plate is used with nail holes, it is better to leave the width and height fields of cast plate blank in the "Anchor rods" tab and let the cast plate size be derived from the values defined in the "Nail holes" tab.

Image
013


This ensures the nail holes are automatically moved accordingly when the cast plate dimensions change or when the cast plate is offset.

Image
image075.png
Base plate with

Choose with what the base plate should be created.

The options are:

  • Default - the default value is "Bolts".
  • Bolts
  • Anchor rods
  • Custom part
  • Bolts and custom part
  • Anchor rods with custom comp part

Bolts

Image
image077.png

Anchor rods

Image
image078.png

In the options Custom part, Bolts and custom part, Anchors with custom component part a custom component of the type Part can be used. 
There are for example anchor rod caps (which are created in a custom component of the type Part) used to ensure during casting the threaded area of the anchor rod stays clear of concrete.

Image
image079.png
Reference Point

Select the reference point.

The options are:

  • Default
  • Top footplate
  • Bottom footplate
Part name componentSelect the custom component of the type Part and the used component setting.
MirrorOption to mirror the custom component. 
Add as subassembly

Decide, whether the custom part should be added as subassembly.

Option:

  • Default
  • No
  • To castplate
  • To footplate

No
 

 

The custom component of the type Part (e.g. Anchor rod caps) are not added, but are loose parts (to transport). 

Image
image083.png
To cast plate

The custom components of the type Part (e.g. Anchor rod caps) are added as subassembly to the cast plate.

Image
image084.png
To foot plate

The custom components of the type Part (e.g. Anchor rod caps) are added as subassembly to the foot plate.

Image
image085.png
1

Define nut height. 

As a default value the anchor diameter is applied. 

2

Define washer thickness. 

As a default value half the nut height is applied. 

3

Anchor length above the base plate. 

As a default value 35 mm is applied.

4

Distance between cast plate and base plate. 

As a default value 30 mm is applied.

5Define length of the upper thread. 
6

Define anchor length. 

As a default value 450 mm is applied.

7Select the anchor rod types. 
Image
image086.png
Standard

AutoDefaults can change this option.
Image
image087.png
Straight anchor rods.
Image
image088.png
Anchor rods 90 degrees. The anchor length is counted from the bottom line of the anchor rods. 
Image
image089.png
Anchor rods 180 degrees (height bended part defined from rod bottom)
Image
image090.png
Straight anchor rods + extra plate at the bottom
Image
014
Anchor rods 90 degrees. The anchor length is counted from the centerline of the anchor rods. 
Image
image091.png
Anchor rods 180 degrees (height bended part defined from rod centerline)
8Define hook radius. 
9Define hook width. 
10Define hook height. 
11Define length beneath extra plate. 
12Define length of threaded rod on bottom side anchor.
13

Choose the hook direction. 

It only effects anchor rods when hook anchors are applied. 

The following options are available: 

Image
image097.png
Standard

Type 1

AutoDefaults can change this option.
Image
image098.png
Parallel to the flanges, outwards.
Image
image099.png
Parallel to the web, outwards.
Image
image100.png
Parallel to the flanges, inwards.
Image
image101.png
Parallel to the web, inwards.  
14Activate the selection boxes to define if the anchor nuts, washer and extra plates are created.
15Activate the selection boxes to define if the anchor nuts, washers and extra plates are welded to the anchor rod.
Cast plate holes tolerance 

Extra tolerance for the cast plate holes and base plate for the anchor rods. 

As a default value 2 mm is applied.

Weldings of anchorbar

Decide, to which part the anchorbar is welded. 

The options are:

  • Default
  • No
  • To castplate
  • To footplate
  • To castplate and footplate
Use weld number

A specific weld can be selected to weld the anchorbar. 

The options are:

  • Default
  • Not specified (00)
  • Add to assembly
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Apply rods finish

Here you can indicate whether the finish of the anchors also applies to the rods, nuts, and washers.

The options are:

  • Default
  • To rods
  • To rods, nuts and washers

 

Hidden UDA's

Certain parts receive certain variables, which are written by the component. These are used in the list "anchor list.doc" but also in the anchor plan settings of general arrangement drawings. In addition, single-part drawing setting "anchor" and assembly drawings setting "stelmal".
Tip: use the Model Template "Anchor plan".

After using the command Inquire object, the following variables appear, depending on the part from which the information is requested.

Inquire objectVariableDescription
AnchorsANCHOR_ARadius hook anchor
AnchorsANCHOR_BAnchor width
Anchors, Footplate, CastplateANCHOR_HHeight anchor. The calculated length is always to the midelle of the anchor. Independent on the option you have choosen.
Anchors, Footplate, CastplateBPLATEThickness of the footplate
Anchors, Footplate, CastplateCPLATEThickness of the castplate
Anchors, Footplate, CastplateANCHOR_TYPE

Anchor type

Image
anchor type.png
Anchors, Footplate, CastplateSPACE_ADistance from the anchors to the top of the footplate
Anchors, Footplate, CastplateSPACE_BDistance bottom side footplate - bottom side castplate
   
Footplate, CastplateBPLATE_BLEVBottom side footplate
Footplate, CastplateCPLATE_TLEVTop side castplate
   
NutNUT

Position number of the nut, so where is this nut in the height direction. The top one is number 1.

Image
024

 

Calculating with the variables

Image
025


Next you can use the values, for example in the anchor list. You open the list in Template Editor and add a value field (or edit an existing value field), next use a formula:

Image
026
Image
027

 

Next when you generate the anchor list, the value (which is the result of the formula) is shown (50 + 50 + 10 - 10):

Image
028

Nuts and washers tab

Use the Nuts and washers tab to define nuts and washer properties.

Image
015

 

OptionDescription
Nut profile

Select nut profile. 

The pos-prefix, assembly-prefix, start number, material, name, class and comment can also be defined.

Washer profile

Select washer profile. ¨

The pos-prefix, assembly-prefix, start number, material, name, class and comment can also be defined.

Plate washer

Define plate washer thickness, width and height. 

The pos-prefix, assembly-prefix, start number, material, name, class and comment can also be defined.

Nut 3 height

Define the height of the nut 3. 

Check the picture on the tab to identify the nut 3.

Nut 4 height

Define the height of the nut 4. 

Check the picture on the tab to identify the nut 4.

Washer 2 height / length

Define the height of the washer 2. 

To create the washer 2, define also the washer 2 diameter.

Check the picture on the tab to identify the nut 2.

Washer 2 diameterDefine the diameter of the washer 2.
Plate washer holes tolerance

Define extra hole tolerance between anchor rod and washer hole.

 

if a washer profile without a hole (e.g. D30 profile) is used, no washer hole can be applied.

Create hole in washer

Decide, whether the hole in the washer should be created.

The options are:

  • Default
  • Yes, tolerance
  • No
Create hole in nut

Decide, whether the hole in the nut should be created.

The options are:

  • Default
  • Yes, tolerance
  • No
Washer profile reference line

Decide, how the washer's reference line should be aligned.

The options are:

  • Default - the default value is "Vertically".
  • Vertically
  • Horizontally

Nailholes tab

Use the Nailholes tab to set the nailhole properties and dimensions in the cast plate. Nailholes are used to mount the cast plate to the formwork.

Image
016

 

OptionDescription
Hole sizeDefine the diameter of the nailhole in the cast plate.
1

Define slotted hole dimensions in x- and y-direction.

These fields can also be used to set the tolerance of oversized and tapped holes.

If the value 0 is set, round holes are created.

2

Select how to measure the dimensions for horizontal nailhole group position.

The options are:

  • Left - from the left edge of the secondary part to the leftmost nailhole.
  • Middle - from the center line of the secondary part to the center line of the nailholes.
  • Right - from the right edge of the secondary part to the rightmost nailhole. 
3Define dimension for horizontal nailhole group position.
4Define nailhole edge distance.
Edge distance is the distance from the center of a nailhole to the edge of the part.
5Define number of nailholes.
6Define nailhole spacing.
Use a space to separate nailhole spacing values. Enter a value for each space between nailholes. For example, if there are 3 nailholes, enter 2 values.
7

Select how to measure the dimensions for vertical nailhole group position.

The options are:

  • Top - from the upper edge of the secondary part to the uppermost nailhole.
  • Middle - from the center line of the bolts to the center line of the secondary part.
  • Below - from the lower edge of the secondary part to the lowest bolt. 
8Define dimension for vertical nailhole group position.
9Define which nailholes are deleted from the nailhole group.
Enter the nailhole numbers of the nailholes to be deleted and separate the numbers with a space. nailhole numbers run from left to right and from top to bottom.
Cast plate reference point 

Define whether the cast plate position is set from the column center or bolt group center.

The options are:

  • Default
  • Center of column
  • Center of boltgroup

Column center: 
  

Image
image114.png

Bolt group center: 
  

Image
image115.png
Cast plate offset in connection directionDefine the displacement of cast plate in the direction of the component. 
Cast plate offset in YDefine the displacement of the cast plate in the direction perpendicular to the component direction. 

Extra tab

Use the Extra tab to control the placement, rotation, and profile type (extra profile 1 and 2) at the anchor rod bottom side. Extra profile 2 connects the anchor rod rows to each other.

Image
017

 

OptionDescription
Extra profile 1

Define the first profile. This profile is placed at the bottom of the anchor rods. 

The default profile PL10*100 is applied.

Extra profile 2Define the second profile. This profile connects the anchor rod rows to each other. 
1

Select the extra profile 1 type and direction. 

The following options are available: 

Image
image117.png

Standard
AutoDefaults can change this option.

Image
image118.png
Image
image116.png
Image
image118.png
Image
image120.png
Image
image121.png
Image
image122.png
Image
image123.png
2Define the edge distance of extra profile 1 from the anchor rod center. 

Extra profile 1 

Hole tolerance

Define the hole tolerance of the anchor rod through extra profile 1 at the bottom side of the anchor rods. 

Extra profile 1 

Profile rotation

Select the rotation for extra profile 1. 

The options are:

  • Default
  • Front
  • Top
  • Back
  • Below

Extra profile 1

Round plates

Decide, whether the round plates should be created instead of rectangular plates.

The options are:

  • No
  • Yes
3

Select the extra profile 2 type and direction. 

The following options are available: 

Image
image124.png
Image
image125.png
Image
image126.png
Image
image125.png
Image
image127.png
Image
image128.png
Image
image129.png
Image
image132.png
Image
image131.png
Image
image130.png
Image
image133.png
Image
image134.png
Image
image135.png
Image
image136.png
4Define the edge distance of extra profile 2 from the anchor rod center.
5

Select the extra profile 2 direction. 

There are two options available: parallel to the column web or parallel to the column flanges.

Image
image139.png
Image
image140.png
Image
image141.png
Image
image140.png
Image
image142.png
Image
image143.png
6Define the extra profile 2 extra length, measured from the anchor rod center. 
Extra profile 2 rotation

Select the rotation for extra profile 2. 

The options are:

  • Default
  • Front
  • Top
  • Back
  • Below
Welds of extra profile 2

Decide whether the extra profile 2 should be welded to another part.

The options are:

  • Default
  • No
  • To extra profile
  • To anchor

Grout holes tab

Use the Grout holes tab to control the creation of extra holes in the base plate and/or in the cast plate, for example for galvanizing service holes. 

It is also possible to create DUMMY-profiles at the extra hole positions, which can be read in a Total Station.
The extra holes for the base plate and cast plate can be defined separately, the left fields are used for the base plate, and the right fields are used for the cast plate. 

Image
018

 

OptionDescription
Hole sizeDefine the grout holes diameter.
Bolt standardDefine the grout holes bolt standard.
ToleranceDefine the grout holes tolerance. 
Read data fromDecide, whether the data should be read from dialog or data file.

Grout holes

(left side)

Define whether extra holes and/or DUMMY profiles for the Total Station are created in the base plate.

The options are:

  • Default
  • No
  • In base plate
  • Holes and DUMMIES for TotalStation - the holes and DUMMY-profiles are created in the base plate.
  • Only DUMMIES for TotalStation - the DUMMY-profiles are created in the base plate.
  • In fitting plate 1
  • In fitting plate 2
  • In fitting plate 3

The DUMMY-profiles have the same dimensions as the extra holes.

(It is possible to use dummy profiles in Tekla Structures in order to position anchors using a Total Station, click here for more information.)

Grout holes

(right side)

Define whether extra holes and/or DUMMY profiles for the Total Station are created in the cast plate.

The options are:

  • Default
  • No
  • In cast plate
  • Holes and DUMMIES for TotalStation - the holes and DUMMY-profiles are created in the cast plate.
  • Only DUMMIES for TotalStation - the DUMMY-profiles are created in the cast plate.
  • In base plate - get extra holes in the base plate.
  • In base plate and cast plate - get the same pattern in both baseplate and castplate.
  • In fitting plate 1
  • In fitting plate 2
  • In fitting plate 3
1

Define slotted hole dimensions in x- and y-direction.

These fields can also be used to set the tolerance of oversized and tapped holes.

If the value 0 is set, round holes are created.

2Define the dimension for horizontal grout hole group position.
3Define the dimension for vertical grout hole group position.
4Define the number of grout holes.
5Define the grout hole spacing.
Use a space to separate grout hole spacing values. Enter a value for each space between grout holes. For example, if there are 3 grout holes, enter 2 values.
6Define the number of grout holes.
7Define the grout hole spacing.
Use a space to separate grout hole spacing values. Enter a value for each space between grout holes. For example, if there are 3 grout holes, enter 2 values.
8

Select the grout hole pattern type. The following options are available: 
  

Image
image151.png
DeleteDefine which grout holes are deleted from the grout hole group.
Enter the grout hole numbers of the grout holes to be deleted and separate the numbers with a space. grout hole numbers run from left to right and from top to bottom.
Reference point

Define whether the grout holes group position is set from the column center or bolt group center.

The options are:

  • Default
  • Center of column
  • Center of boltgroup

Extra plate tab

Use the Extra plate tab to add extra vertical plates which for example can be used to mount wall panels.

Image
019

 

OptionDescription
Extra plate

Define the extra plate profile.  

The pos-prefix, start number, material and name can also be defined.

1

Select the option to create extra plates. 

It is optional to create one plate or two plates at any given side of the column, these plates can be parallel or perpendicular orientated to each other. 

It is also possible to create three similar orientated plates. 

Fields a - f can be used, depending on the selected option to define the dimensions and offsets. 

Image
image155.png
Image
image156.png
Image
image157.png
Image
image158.png
Image
image159.png
Image
image160.png
Image
image161.png
Image
image162.png
Image
image163.png
Image
image164.png
Image
image165.png
Image
image166.png
Image
image167.png
Image
image168.png
Image
image169.png
Image
image170.png
Image
image171.png
2Define the overlap/offset of the extra plate from the base plate top.

Concrete tab

Use the Concrete tab to define recesses in case the base plate is created for a concrete column. The recesses can be used to create clearance to mount the bolts or nuts.

Image
020

 

OptionDescription
1

Select the option for welding the base plate. 

The options are:

  • Default
  • Weld footpl to column
  • Cast unit footpl to column
2Select, whether the recesses should be created.
Image
image175.png
Standard

AutoDefaults can change this option.
Image
image176.png
No recesses.
Image
image177.png
Create recesses around the anchor rods/bolts. 
3Define the recesses depth. 
4Define the recesses width. 
5Define the recesses height. 

Analysis tab

Click the link below to find out more:
Analysis tab
 

About

In the About tab, general information about the extension and the developer can be found.

Image
023

All rights reserved. No conclusions can be associated to the representation of the pictures in relation to the operating systems under which Tekla Structures runs.

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc-nd/4.0/ or send a letter to Creative Commons, 444 Castro Street, Suite 900, Mountain View, California, 94041, USA.

Back to top
Invia