Tube seat (104) creates a connection between one RHS rail and a column. The RHS rail collides with the column web. The connection creates a seat plate or an angle.
Objects created
-
Seat plate
-
Angle
-
Bolts
-
Welds
Use for
| Situation | Description |
|---|---|
|
|
Rail connected to a column with an angle. To ensure that the bolts can be tightened, the connection can create either a 45-degree cut in the rail or large holes in the opposite flange for the wrench to go through. |
Selection order
-
Select the main part.
-
Select the secondary part.
The connection is created automatically when the secondary part is selected.
Part identification key

| Description | |
|---|---|
|
1 |
Angle |
Picture tab
Use the Picture tab to define the dimensions and bolt spacing.
Dimensions

| Description | |
|---|---|
|
1 |
Bolt edge distance from the angle upper edge. |
|
2 |
Secondary part edge distance to the column center line. |
|
3 |
Bolt edge distance from the secondary part edge. |

| Description | |
|---|---|
|
1 |
Bolt spacing |
|
2 |
Bolt spacing |
|
3 |
Width of the angle |
Parts tab
Use the Parts tab to define the part properties.
Parts
| Option | Description |
|---|---|
|
Seat plate |
Thickness, width, and height of the seat plate. |
|
Angle |
Select the profile from the profile catalog. |
|
Option |
Description |
Default |
|---|---|---|
|
Pos_No |
Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number. |
The default part start number is defined in the Components settings in . |
|
Material |
Material grade. |
The default material is defined in the Part material box in the Components settings in . |
|
Name |
Name that is shown in drawings and reports. |
Parameters tab
Use the Parameters tab to define the secondary part cut, attachment, dimensions, offset, and hole creation.
Angle to column
There are two options that you can use to connect an angle to the RHS column.
| Option | Description |
|---|---|
|
Big holes |
Large holes of the same type and diameter as the rails. |
|
Outer flange |
Bolts that fully cross the column. This may lead to very long bolts that may not exist in the bolt catalog. |
Secondary part cut
| Option | Description |
|---|---|
|
|
Secondary part is not cut. |
|
|
Secondary part is cut. |
Seat plate/angle attachment
| Option | Description |
|---|---|
|
|
Seat plate is welded to the main part. |
|
|
Angle is welded to the main part. |
|
|
Angle is bolted to the main part. |
Dimensions

| Description | |
|---|---|
|
1 |
Chamfer dimension |
|
2 |
Seat plate edge distance from the main part edge |
|
3 |
Hole diameter |

| Description | |
|---|---|
|
1 |
Beam cut angle |
Offset

| Description | |
|---|---|
|
1 |
Seat or angle offset from the column center line. |
Hole creation
| Option | Description |
|---|---|
|
|
Holes are created in the secondary part upper flange. |
|
|
Bolts are created in the secondary part upper flange. |
Secondary bolts tab
Use the Secondary bolts tab to define the bolt properties of the secondary part bolts.
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
Bolt assembly
The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.
If you want to create a hole only, clear all the check boxes.
To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.
Bolt length increase
Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.
Primary bolts tab
Use the Primary bolts tab to define the bolt properties of the main part bolts.
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
General tab
Click the link below to find out more:
Analysis tab
Click the link below to find out more:
Welds
Click the link below to find out more:







