Seat type 5 (60) connects a beam to a beam or column flange with a seat profile. The secondary part can be sloped, skewed, or rotated.
Objects created
-
Seat profile
-
Bolts
-
Welds
Use for
| Situation | Description |
|---|---|
|
|
Beam connected to a beam flange with a seat profile The main part can have a W, TS, L, WT, or C main profile type. The secondary part can have a W, L, WT, or C profile type. |
|
|
Beam is sloped or skewed. Square end fitting and seat rotation options are used. |
Selection order
-
Select the main part (column or beam).
-
Select the secondary part (beam).
The connection is created automatically when the secondary part is selected.
Part identification key

| Description | |
|---|---|
|
1 |
Seat profile |
Picture tab
Use the Picture tab to define the connection dimensions.
Dimensions

| Description | |
|---|---|
|
1 |
Horizontal offset of the seat, perpendicular to the seat axis or direction The distance is measured from the main part center line to the back of the seat. |
|
2 |
Gap between the top flange of the main part and the seat |
|
3 |
Secondary part edge distance at the top to the seat edge |
Parts tab
Use the Parts tab to define the part properties.
Parts
| Option | Description |
|---|---|
|
Seat profile |
Select the profile from the profile catalog. Define the seat length if there are no bolts. |
|
Option |
Description |
Default |
|---|---|---|
|
Pos_No |
Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number. |
The default part start number is defined in the Components settings in . |
|
Material |
Material grade. |
The default material is defined in the Part material box in the Components settings in . |
|
Name |
Name that is shown in drawings and reports. |
Parameters tab
Use the Parameters tab to define the seat position, angle, rotation, and secondary part fitting.
Seat position
| Option | Description |
|---|---|
|
|
Default Seat profile is placed parallel to the main part. AutoDefaults can change this option. |
|
|
Automatic Seat profile is placed parallel to the main part. |
|
|
Seat profile is placed parallel to the main part. |
|
|
Seat profile is placed perpendicular to the secondary part. |
|
|
Seat profile is placed by the angle value that you define. |
Seat angle

| Description | |
|---|---|
|
1 |
Define the angle value in degrees. The angle is measured relative to the main part center line. |
Seat rotation
| Option | Description |
|---|---|
|
|
Default Longer leg of the seat is vertical. AutoDefaults can change this option. |
|
|
Longer leg of the seat is vertical. |
|
|
Longer leg of the seat is horizontal. |
Secondary part fitting
| Option, top | Option, bottom | Description |
|---|---|---|
|
|
|
Default Bevel cut AutoDefaults can change this option. |
|
|
|
Bevel cut |
|
|
|
Square cut |
Bolts tab
Use the Bolts tab to define the bolt group dimensions and bolt properties.
Bolt group dimensions

| Description | |
|---|---|
|
1 |
Dimension for vertical bolt group position. |
|
2 |
Dimension for horizontal bolt group position. |
|
3 |
Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part. |
|
4 |
Number of bolts. |
|
5 |
Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values. |
| Option | Description |
|---|---|
|
Seat Z offset (If no bolts) |
Define the Z offset for the seat in situations where bolts are not created. |
|
Edge tolerance for deleting bolts |
Bolts that are located within the defined edge tolerance value are automatically deleted. |
|
Eliminate bolts |
Define which bolts are deleted from the bolt group. Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom. |
Bolt basic properties
|
Option |
Description |
Default |
|---|---|---|
|
Bolt size |
Bolt diameter. |
Available sizes are defined in the bolt assembly catalog. |
|
Bolt standard |
Bolt standard to be used inside the component. |
Available standards are defined in the bolt assembly catalog. |
|
Tolerance |
Gap between the bolt and the hole. |
|
|
Thread in mat |
Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used. |
Yes |
|
Site/Workshop |
Location where the bolts should be attached. |
Site |
Slotted holes
You can define slotted, oversized, or tapped holes.
|
Option |
Description |
Default |
|---|---|---|
|
1 |
Vertical dimension of slotted hole. |
0, which results in a round hole. |
|
2 |
Horizontal dimension of slotted hole, or allowance for oversized holes. |
0, which results in a round hole. |
|
Hole type |
Slotted creates slotted holes. Oversized creates oversized holes. No hole does not create holes. Tapped creates tapped holes. |
|
|
Rotate Slots |
When the hole type is Slotted, this option rotates the slotted holes. |
|
|
Slots in |
Part(s) in which slotted holes are created. The options depend on the component in question. |
Bolt assembly
The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.
If you want to create a hole only, clear all the check boxes.
To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.
Bolt length increase
Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.
Special holes for bolts
| Option | Description |
|---|---|
|
|
Default Holes are not created. AutoDefaults can change this option. |
|
|
Holes are not created. |
|
|
Holes are created in the part. |
|
|
Holes are created in the seat. |
|
|
Holes are created both in the part and the seat. |
Bolt pattern
Bolt patterns are oriented relative to the main part. Bolt patterns are used when the seat position is set perpendicular to the secondary part.
| Option | Description |
|---|---|
|
|
Default Square pattern AutoDefaults can change this option. |
|
|
Automatic Square pattern |
|
|
Square pattern |
|
|
Bevel pattern |
|
|
Square shifted pattern |
|
|
Bevel shifted pattern |
|
|
Square staggered pattern |
|
|
Bevel staggered pattern |
|
|
No bolts |
General tab
Click the link below to find out more:
Analysis tab
Click the link below to find out more:
Welds
Click the link below to find out more:




























