Pipe column and beam panel zone (21) connects a beam to a column with a diaphragm that goes through the column at the level of the beam flanges. You can use Pipe column and beam panel zone (21) both for square and round steel columns. H profile beams are used as secondary parts. The secondary part beams can be either horizontal or skewed.
Objects created
-
Diaphragm (penetrating, inner)
-
Brackets
-
Cantilevers
-
Welds
Use for
| Situation | Description |
|---|---|
|
|
Beams connected to a column with brackets and cantilevers. |
Selection order
-
Select the main part (lower column).
-
Select the secondary parts (a maximum of 4 beams).
-
Select the upper column as the fifth secondary part, if needed.
-
Click the middle mouse button to create the connection.
Part identification key

| Description | |
|---|---|
|
1 |
Diaphragm |
|
2 |
Short columm Short columns are created between penetrating diaphragms. |
|
3 |
Tapered column-beam stub (150) connection |
Design dimensions tab
Use the Design dimensions tab to define the bracket type and length, and haunch height.
Bracket and hauch
| Option | Description | Default |
|---|---|---|
|
Bracket type |
Select the bracket type.
|
Bracket |
|
Bracket length |
When you have set the bracket type to Bracket, select whether the bracket length is based on Reference point (L2) (this is the default) or Center point (L1). The length is based on the lower column.
|
1000 mm |
|
Haunch |
Select whether the haunch height is automatically determined. You can use this option when the bracket type is Bracket. |
None |
|
Haunch height |
Define the haunch height when the bracket type is not cantilever and you have set Haunch to Specified. |
Straight bracket of the same size as the beam |
Fabrication dimensions tab
Use the Fabrication dimensions tab to define the diaphragm dimensions.
Dimensions

| Description | Default | |
|---|---|---|
|
1 |
Gap between the column and the diaphragm |
0 mm |
|
2 |
Maximum diaphragm thickness |
40 mm |
|
3 |
Outer additional diaphragm thickness |
0 mm |
|
5 |
Inner additional diaphragm thickness |
0mm |
Inner diaphragm dimensions

| Description | Default | |
|---|---|---|
|
1 |
Chamfer shape of the inner diaphragm corner |
Inner diaphragm: Concave circle Penetrating diaphragm: No chamfer |
|
2 |
Corner chamfer dimension |
|
|
3 |
Corner chamfer dimension for the extra arc |
|
|
4 |
Gap between the inner diaphragm and the inner surface of the column |
0 mm |
|
5 |
Spacing of the four corner holes of the inner diaphragm This option is used when the corner hole diameter defined in 6 is > 0 mm. |
100 mm |
|
6 |
Diameter of the corner hole that goes through the diaphragm There are four corner holes. You can define the diameter when the column is a square steel pipe. |
0 mm |
|
7 |
Diameter of the center hole that goes through the diaphragm |
30 mm |
Penetrating diaphragm dimensions

| Description | Description | |
|---|---|---|
|
1 |
Corner chamfer shape of the penetrating diaphragm |
Inner diaphragm: Concave circle Penetrating diaphragm: No chamfer |
|
2 |
Corner chamfer dimension You can define the dimension when the chamfer shape is set to something else than No. |
0 mm |
|
3 |
Diaphragm protrusion dimensions |
25 mm |
|
4 |
Spacing of the four corner holes of the through diaphragm This option is used when the corner hole diameter defined in 5 is > 0 mm. |
100 mm |
|
5 |
Diameter of the corner hole that goes through the diaphragm There are four corner holes. You can define the diameter when the column is a square steel pipe. |
|
|
6 |
Diameter of the center hole that goes through the diaphragm |
30 mm |
|
7 |
Top plate is a penetrating diaphragm, called a top plate if there is no upper column. |
Weld access holes
You can define the weld access holes for the diaphragm plates.

Clearance dimensions

| Description | Default | |
|---|---|---|
|
1 |
Clearance between the inner diaphragms |
100 mm |
|
2 |
Clearance between the penetrating and inner diaphragms |
100 mm |
|
3 |
Clearance between the penetrating diaphragms |
150 mm |
Panel parts tab
Use the Panel parts tab to define the part properties.
Parts
| Option | Description |
|---|---|
|
Tapered plates |
Thickness of the four tapered plates that build the short column. You can define the thickness when the taper type and straight short column type is Buildup. |
|
Straight plates |
Thickness of the four straight plates that build the short column. You can define the thickness when the taper type and straight short column type is Buildup. |
|
Tapered profile |
Select the profile from the profile catalog. Short column profile name can be used when the taper type and straight short column type is Rolled. |
|
Straight profile |
Select the profile from the profile catalog. Short column profile name can be used when the taper type and straight short column type is Rolled. |
|
Option |
Description |
Default |
|---|---|---|
|
Pos_No |
Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number. |
The default part start number is defined in the Components settings in . |
|
Material |
Material grade. |
The default material is defined in the Part material box in the Components settings in . |
|
Name |
Name that is shown in drawings and reports. |
|
|
Finish |
Describes how the part surface has been treated. |
Rotation of rolled steel
Rolled steel is placed at the center axis of the main part. If you use a rolled tapered profile, the taper may be eccentric. You then need to change the rotation by using the Taper profile orientation option.
| Option | Description | Default |
|---|---|---|
|
Panel plate size up |
Increased panel thickness |
0 increase |
|
Taper panel |
Select whether to taper the panel. You can define an additional rotation angle to the main part rotation angle. |
Auto |
|
Taper type |
Select the tapering type. |
Buildup |
|
Taper profile orientation |
Select the rotation direction of the tapered profile. The rotation follows the global coordinate system. If the tapering type of the short column is Buildup, you can use this setting to change the preferred direction of plates. |
Front |
|
Straight short column type |
Select the short column type. |
Rolled |

Diaphragm thickness increase
| Option | Regular plate size up | Plate size up | Size up due to column |
|---|---|---|---|
|
Penetrating diaphragm Inner diaphragm |
The default values are:
|
To increase the size of a plate, set the size increase. You can define two size up values for each diaphragm plate, for a thin plate and a thick plate. For example,
If the required plate thickness is 34 mm, 2 size ups are applied and the result will be 45 mm. If the required plate thickness is 44 mm, 1 size up is applied and the result will be 50 mm. |
Increased plate size The default values are:
|
The table below shows an example of the calculation result.
| Normal size up = 2 | Specified plate thickness | Plate size up = 1 |
|---|---|---|
|
|
|
Welds
| Option | Description |
|---|---|
|
Weld prep |
Select whether to create welding cuts. The default is No. |
|
Weld prep. preset |
Select whether to use preset welding settings. |
Custom component to column
You can use custom components for welds, welding cuts, and weld backing bars.
| Option | Description |
|---|---|
|
Component |
Custom component name You can use seam or connection type custom components. |
|
Parameters |
Property file name to be used for the custom component. You can define the name if you have specified a custom component. |
Diaphragm tab
Use the Diaphragm tab to define the diaphragm material, thickness, offset, and type.
Diaphragm

| Description | |
|---|---|
|
1 |
Diaphragm plate thickness |
|
2 |
Offset from the automatically determined diaphragm position |
|
3 |
Diaphragm type |
Diaphragm thickness
Apply the highest value of the following options:
-
Thickness is determined based on the thickest plate among the beam flanges that are at the same height.
-
Thickness is determined by the thickest beam flange value + the additional thicknesses defined on the Fabrication dimensions tab.
-
Thickness is calculated based on the required diaphragm thickness, which takes into account each beam flange thickness and height.

Diaphragm offset
The diaphragm offset is based on the automatically determined diaphragm height. The offset value is the distance from the reference height. Use the offset when fine-tuning the height of the automatically determined diaphragm. Enter a positive value for the upward offset and a negative value for the downward offset.
Diaphragm type
The diaphragm height is automatically determined by the height at which the beam flanges meet.
| Example | Description |
|---|---|
|
|
The example image shows the most commonly used diaphragm arrangement. The outermost upper and lower diaphragms are penetrating diaphragms. The other diaphragm is an inner diaphragm. |
|
|
Even if two or more flanges are on slightly different levels, one diaphragm is created if the clearance is smaller than the minimum diaphragm clearance set on the Fabrication dimensions tab. |
Cantilevers tab
Use the Cantilevers tab to define the custom components that are used.
Custom components
You can define that a custom component is used for the upper flange, lower flange, and the web.
|
Component |
Custom component name You can use seam or connection type custom components. |
|
Parameters |
Property file name to be used for the custom component. You can define the name if you have specified a custom component. |
Custom components (upper flange, lower flange)
You can use custom components for welds, welding cuts, and weld backing bars.
The images below show examples of custom components applied to beam flanges.


Custom components (web)
You can use custom components for polygon welds and web cuts.
The beam is the main part and the short column is the secondary part. If the web welds are separated by a penetrating diaphragm, apply a custom component to each web edge.
The example image below shows a situation where the penetrating diaphragm is interrupted and the side of the beam web is divided into two.

The example image below shows the coordinate system, and the first and second points used to define a seam type custom component.

Bracket tab
Use the Bracket tab to define the bracket properties.
Properties
| Option | Description |
|---|---|
|
Parameters |
Property file name to be used for Tapered column-beam stub (150). Define this when you have selected Bracket as the Bracket type on the Design dimensions tab. |
|
Profile name |
Select the profile from the profile catalog. The default value is the beam profile when the beam is rolled. |
|
Size up |
Plate size increase If you have selected a profile, the profile size value is used. |
|
Profile/Flg |
Select the profile/flange plate material. |
|
Web |
Select the web plate material. This option is not used when the bracket type is Rolled. |
General tab
Click the link below to find out more:
Design tab
Click the link below to find out more:
Analysis tab
Click the link below to find out more:
Welds
Click the link below to find out more:




